Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual: Internal Control Module Random Access Memory (RAM) Error Data Memory Failure (P060444)

Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual / Engine & Hybrid System / 2gr-fks (engine Control) / Sfi System / Internal Control Module Random Access Memory (RAM) Error Data Memory Failure (P060444)

MONITOR DESCRIPTION

The ECM continuously monitors its internal memory status. This self-check ensures that the ECM is functioning properly. The ECM memory status is diagnosed by internal mirroring of the main CPU and sub CPU to detect Random Access Memory (RAM) errors. If outputs from these CPUs are different and deviate from the standard, the ECM will illuminate the MIL and store this DTC.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

Note

P060444

Internal Control Module Random Access Memory (RAM) Error Data Memory Failure

ECM RAM error (1 trip detection logic).

ECM

Comes on

DTC stored

SAE Code: P0604

MONITOR STRATEGY

Related DTCs

P0604: Internal control module random access memory error (RAM error on electronic throttle control)

Required Sensors/Components (Main)

ECM

Required Sensors/Components (Related)

-

Frequency of Operation

Continuous

Duration

6 times

MIL Operation

Immediate

Sequence of Operation

None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever the following DTCs are not stored

None

TYPICAL MALFUNCTION THRESHOLDS

RAM mirror check

Fail

CONFIRMATION DRIVING PATTERN

HINT:

  • After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

    Click here

  • When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.

    Click here

  1. Connect the Techstream to the DLC3.
  2. Turn the engine switch on (IG).
  3. Turn the Techstream on.
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Turn the Techstream off.
  6. Turn the engine switch off.
  7. Disconnect the Techstream.
  8. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
  9. Connect the cable to the negative (-) battery terminal.
  10. Connect the Techstream to the DLC3.
  11. Turn the engine switch on (IG).
  12. Turn the Techstream on.
  13. Wait 16 seconds or more [A].
  14. Enter the following menus: Powertrain / Engine / Trouble Codes [B].
  15. Read the pending DTCs.

    HINT:

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  16. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  17. Input the DTC: P060444.
  18. Check the DTC judgment result.

    Techstream Display

    Description

    NORMAL

    • DTC judgment completed
    • System normal

    ABNORMAL

    • DTC judgment completed
    • System abnormal

    INCOMPLETE

    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions

    HINT:

    • If the judgment result is NORMAL, the system is normal.
    • If the judgment result is ABNORMAL, the system is malfunctioning.
    • [A] to [B]: Normal judgment procedure.

      The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

    • When clearing the permanent DTCs, do not disconnect the cable from the battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.

CAUTION / NOTICE / HINT

NOTICE:

After turning engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here

HINT:

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.

READ OUTPUT DTC (DTC P060444)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Clear the DTCs.

Powertrain > Engine > Clear DTCs

(e) Turn the engine switch off and turn the Techstream off.

(f) Disconnect the Techstream.

(g) Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

(h) Connect the cable to the negative (-) battery terminal.

(i) Connect the Techstream to the DLC3.

(j) Turn the engine switch on (IG).

(k) Turn the Techstream on.

(l) Wait 16 seconds or more.

(m) Enter the following menus: Powertrain / Engine / Trouble Codes.

(n) Read the DTCs.

Powertrain > Engine > Trouble Codes

Result

Proceed to

DTCs are not output

A

DTC P060444 is output

B

A

CHECK FOR INTERMITTENT PROBLEMS

B

REPLACE ECM

    Thermostat Heater Control Circuit Short to Ground or Open (P059714)
    DESCRIPTION Refer to DTC P059712. Click here DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note P059714 Thermostat Heater Control Circuit Short to Groun ...

    Control Module Performance Bank 2 Component Internal Failure (P060596,P060796)
    MONITOR DESCRIPTION The ECM continuously monitors its internal processors (CPUs) and heated oxygen sensor transistors. This self-check ensures that the ECM is functioning properly. DTC No. Detect ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Smart Access System With Push-button Start (for Start Function): Parts Location
    PARTS LOCATION ILLUSTRATION *1 PARK / NEUTRAL POSITION SWITCH *2 SEMICONDUCTOR PWR INTEGRATION ECU *3 ST RELAY *4 STARTER ASSEMBLY *5 ECM *6 IG2 RELAY *7 IG2 FUSE *8 IG2-MAIN FUSE *9 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY - IG1-MAIN RELAY - ...

    Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Airbag System: Curtain Shield Airbag Sensor Initialization Error (LH) (B1638)
    DESCRIPTION The side collision sensor LH circuit (bus 1) consists of the airbag sensor assembly, door side airbag sensor LH and rear airbag sensor LH. The door side airbag sensor LH and rear airbag sensor LH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2024 Copyright www.lexusrx.net
    0.0148