Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual: Switch Failure (B2342)
DESCRIPTION
This DTC is stored when the sliding roof ECU (sliding roof drive gear assembly) or roof sunshade ECU (sliding roof drive gear assembly) detects that the map light assembly is stuck for 30 seconds or more.
Sliding Roof| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2342 | Switch Failure | Sliding roof ECU (sliding roof drive gear assembly) detects map light assembly is stuck for 30 seconds or more. |
|
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2342 | Switch Failure | Roof sunshade ECU (sliding roof drive gear assembly) detects map light assembly is stuck for 30 seconds or more. |
|
WIRING DIAGRAM
Refer to DTC B2341.
Click here .gif)
CAUTION / NOTICE / HINT
NOTICE:
-
If the sliding roof ECU (sliding roof drive gear assembly) or roof sunshade ECU (sliding roof drive gear assembly) is removed and reinstalled or replaced, the sliding roof ECU (sliding roof drive gear assembly) or roof sunshade ECU (sliding roof drive gear assembly) must be initialized.
Click here
-
The panoramic moon roof system uses the LIN communication system. First, confirm that there are no malfunctions in the LIN communication system. Refer to How to Proceed with Troubleshooting.
Click here
- DTC B2342 is stored in the sliding roof ECU (sliding roof drive gear assembly) and roof sunshade ECU (sliding roof drive gear assembly).
PROCEDURE
| 1. | CHECK FOR DTC |
(a) Clear the DTCs.
Click here
(b) Check for DTCs.
Click here
OK:
DTC B2342 is not output.
| OK | .gif) | END (DUE TO SWITCH BEING OPERATED FOR 30 SECONDS OR MORE) |
|
.gif)
| 2. | CHECK DTC OUTPUT |
(a) Check the parts from which this DTC has been output.
| Result | Proceed to |
|---|---|
| DTC output from sliding roof ECU (sliding roof drive gear assembly) | A |
| DTC output from roof sunshade ECU (sliding roof drive gear assembly) | B |
| B | | GO TO STEP 6 |
|
| 3. | READ VALUE USING TECHSTREAM (SLIDING ROOF) |
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Sliding Roof / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Sliding Roof > Data List| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Current Roof Open Switch Stuck ON | Sliding roof open switch stuck signal (Current) | OFF or ON | OFF: No sliding roof switch stuck signal (Current) ON: Sliding roof switch stuck signal (Current) | - |
| Current Roof Close Switch Stuck ON | Sliding roof close switch stuck signal (Current) | OFF or ON | OFF: No sliding roof switch stuck signal (Current) ON: Sliding roof switch stuck signal (Current) | - |
| Current Shade Close Switch Stuck ON | Roof sunshade close switch stuck signal (Current) | OFF or ON | OFF: No roof sunshade switch stuck signal (Current) ON: Roof sunshade switch stuck signal (Current) | - |
| Current Shade Open Switch Stuck ON | Roof sunshade open switch stuck signal (Current) | OFF or ON | OFF: No roof sunshade switch stuck signal (Current) ON: Roof sunshade switch stuck signal (Current) | - |
| Past Roof Open Switch Stuck ON | Sliding roof open switch stuck signal (Past) | OFF or ON | OFF: No sliding roof switch stuck signal (Past) ON: Sliding roof switch stuck signal (Past) | - |
| Past Roof Close Switch Stuck ON | Sliding roof close switch stuck signal (Past) | OFF or ON | OFF: No sliding roof switch stuck signal (Past) ON: Sliding roof switch stuck signal (Past) | - |
| Past Shade Close Switch Stuck ON | Roof sunshade close switch stuck signal (Past) | OFF or ON | OFF: No roof sunshade switch stuck signal (Past) ON: Roof sunshade switch stuck signal (Past) | - |
| Past Shade Open Switch Stuck ON | Roof sunshade open switch stuck signal (Past) | OFF or ON | OFF: No roof sunshade switch stuck signal (Past) ON: Roof sunshade switch stuck signal (Past) | - |
| Current Vent Switch Stuck ON | Sliding roof tilt switch stuck signal (Current) | OFF or ON | OFF: No sliding roof switch stuck signal (Current) ON: Sliding roof switch stuck signal (Current) | - |
| Past Vent Switch Stuck ON | Sliding roof tilt switch stuck signal (Past) | OFF or ON | OFF: No sliding roof switch stuck signal (Past) ON: Sliding roof switch stuck signal (Past) | - |
| Tester Display |
|---|
| Current Roof Open Switch Stuck ON |
| Current Roof Close Switch Stuck ON |
| Current Shade Close Switch Stuck ON |
| Current Shade Open Switch Stuck ON |
| Past Roof Open Switch Stuck ON |
| Past Roof Close Switch Stuck ON |
| Past Shade Close Switch Stuck ON |
| Past Shade Open Switch Stuck ON |
| Current Vent Switch Stuck ON |
| Past Vent Switch Stuck ON |
OK:
OFF appears on the Techstream screen.
| OK | | REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) |
|
| 4. | CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - MAP LIGHT ASSEMBLY) |
(a) Disconnect the U2 sliding roof ECU (sliding roof drive gear assembly) connector.
(b) Disconnect the U11 map light assembly connector.
(c) Disconnect the w1 roof sunshade ECU (sliding roof drive gear assembly) connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| U2-10 (OPN) or U11-11 (OPN) - Body ground | Always | 10 kΩ or higher |
| U2-8 (CLS) or U11-12 (CLS) - Body ground | Always | 10 kΩ or higher |
| U2-4 (TILT) or U11-7 (B) - Body ground | Always | 10 kΩ or higher |
| U2-5 (OPN) or U11-23 (UP) - Body ground | Always | 10 kΩ or higher |
| U2-9 (CLS) or U11-24 (DOWN) - Body ground | Always | 10 kΩ or higher |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
| 5. | INSPECT MAP LIGHT ASSEMBLY |
(a) Remove the map light assembly.
Click here
(b) Inspect the map light assembly.
Click here
| OK | | REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) |
| NG | | REPLACE MAP LIGHT ASSEMBLY |
| 6. | READ VALUE USING TECHSTREAM (SLIDING SUNSHADE) |
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Sliding Sunshade / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Sliding Sunshade > Data List| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Current Roof Open Switch Stuck ON | Sliding roof open switch stuck signal (Current) | OFF or ON | OFF: No sliding roof switch stuck signal (Current) ON: Sliding roof switch stuck signal (Current) | - |
| Current Roof Close Switch Stuck ON | Sliding roof close switch stuck signal (Current) | OFF or ON | OFF: No sliding roof switch stuck signal (Current) ON: Sliding roof switch stuck signal (Current) | - |
| Current Shade Close Switch Stuck ON | Roof sunshade close switch stuck signal (Current) | OFF or ON | OFF: No roof sunshade switch stuck signal (Current) ON: Roof sunshade switch stuck signal (Current) | - |
| Current Shade Open Switch Stuck ON | Roof sunshade open switch stuck signal (Current) | OFF or ON | OFF: No roof sunshade switch stuck signal (Current) ON: Roof sunshade switch stuck signal (Current) | - |
| Past Roof Open Switch Stuck ON | Sliding roof open switch stuck signal (Past) | OFF or ON | OFF: No sliding roof switch stuck signal (Past) ON: Sliding roof switch stuck signal (Past) | - |
| Past Roof Close Switch Stuck ON | Sliding roof close switch stuck signal (Past) | OFF or ON | OFF: No sliding roof switch stuck signal (Past) ON: Sliding roof switch stuck signal (Past) | - |
| Past Shade Close Switch Stuck ON | Roof sunshade close switch stuck signal (Past) | OFF or ON | OFF: No roof sunshade switch stuck signal (Past) ON: Roof sunshade switch stuck signal (Past) | - |
| Past Shade Open Switch Stuck ON | Roof sunshade open switch stuck signal (Past) | OFF or ON | OFF: No roof sunshade switch stuck signal (Past) ON: Roof sunshade switch stuck signal (Past) | - |
| Current Vent Switch Stuck ON | Sliding roof tilt switch stuck signal (Current) | OFF or ON | OFF: No sliding roof switch stuck signal (Current) ON: Sliding roof switch stuck signal (Current) | - |
| Past Vent Switch Stuck ON | Sliding roof tilt switch stuck signal (Past) | OFF or ON | OFF: No sliding roof switch stuck signal (Past) ON: Sliding roof switch stuck signal (Past) | - |
| Tester Display |
|---|
| Current Roof Open Switch Stuck ON |
| Current Roof Close Switch Stuck ON |
| Current Shade Close Switch Stuck ON |
| Current Shade Open Switch Stuck ON |
| Past Roof Open Switch Stuck ON |
| Past Roof Close Switch Stuck ON |
| Past Shade Close Switch Stuck ON |
| Past Shade Open Switch Stuck ON |
| Current Vent Switch Stuck ON |
| Past Vent Switch Stuck ON |
OK:
OFF appears on the Techstream screen.
| OK | | REPLACE ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) |
|
| 7. | CHECK HARNESS AND CONNECTOR (ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - MAP LIGHT ASSEMBLY) |
(a) Disconnect the w1 roof sunshade ECU (sliding roof drive gear assembly) connector.
(b) Disconnect the U11 map light assembly connector.
(c) Disconnect the U2 sliding roof ECU (sliding roof drive gear assembly) connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| w1-10 (OPN) or U11-11 (OPN) - Body ground | Always | 10 kΩ or higher |
| w1-8 (CLS) or U11-12 (CLS) - Body ground | Always | 10 kΩ or higher |
| w1-4 (VENT) or U11-7 (B) - Body ground | Always | 10 kΩ or higher |
| w1-5 (OPN) or U11-23 (UP) - Body ground | Always | 10 kΩ or higher |
| w1-9 (CLS) or U11-24 (DOWN) - Body ground | Always | 10 kΩ or higher |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
| 8. | INSPECT MAP LIGHT ASSEMBLY |
(a) Remove the map light assembly.
Click here
(b) Inspect the map light assembly.
Click here
| OK | | REPLACE ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) |
| NG | | REPLACE MAP LIGHT ASSEMBLY |
Sensor (Motor) Failure (B2341,B2344)
DESCRIPTION When the sliding roof ECU (sliding roof drive gear assembly) or roof sunshade ECU (sliding roof drive gear assembly) detects a motor malfunction and the sliding roof and roof sunshade oper ...
Position Initialization Incomplete (B2343)
DESCRIPTION This DTC is stored when the sliding roof ECU (sliding roof drive gear assembly) or roof sunshade ECU (sliding roof drive gear assembly) has not been initialized. Sliding Roof DTC No. ...
Other materials:
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Rear Door Outside Moulding: Installation
INSTALLATION CAUTION / NOTICE / HINT HINT:
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
PROCEDURE 1. INSTALL NO. 3 REAR DOOR WEATHERSTRIP (a) Engage the 7 clips to install the No. 3 rear door weatherstrip. 2. INSTALL REAR DOOR LOWER OUTSIDE ...
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Automatic Transaxle System: Shift Solenoid "A" Circuit Short to Ground (P075011)
DESCRIPTION Changing gears is performed by the ECM turning the shift solenoid valves SL1, SL2, SL3, SL4, SL5, S1 and S2 on and off. If an open or short occurs in any of the shift solenoid valve circuits, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be driven. I ...
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual
- For your information
- Pictorial index
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Lexus Display Audio system
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual
0.0136