CAUTION / NOTICE / HINT
HINT:
PROCEDURE
| 1. | VEHICLE BROUGHT TO WORKSHOP |
|
| 2. | CUSTOMER PROBLEM ANALYSIS CHECK |
HINT:
| What | Vehicle model, system name |
| When | Date, time, occurrence frequency, whether the problem occurred recently or has been occurring for a long time |
| Where | Whether the problem occurs at a specific location |
| Under what conditions? | Whether the doors were locked or unlocked, whether the engine switch was on (IG), whether the engine has started |
| How did it happen? | Problem symptoms |
|
| 3. | PRE-CHECK |
(a) Measure the battery voltage.
Standard Voltage:
11 to 14 V
If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.
(b) Check the fuses and relays.
(c) Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.
|
| 4. | CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM* |
(a) Using the Techstream, check for CAN communication system DTCs.
Click here
| Result | Proceed to |
|---|---|
| CAN DTCs are not output | A |
| CAN DTCs are output | B |
| B | | GO TO CAN COMMUNICATION SYSTEM |
|
| 5. | CHECK COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM* |
(a) Using the Techstream, check for LIN communication system DTCs.
Click here
| Result | Proceed to |
|---|---|
| LIN DTCs are not output | A |
| LIN DTCs are output | B |
| B | | GO TO LIN COMMUNICATION SYSTEM |
|
| 6. | CHECK FOR DTC (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)* |
(a) Clear the DTCs.
Click here
(b) Recheck for DTCs.
Body Electrical > Master Switch > Trouble Codes| Result | Proceed to |
|---|---|
| DTC B2312 is not output | A |
| DTC B2312 is output | B |
| B | | GO TO POWER WINDOW CONTROL SYSTEM |
|
| 7. | CHECK FOR DTC (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))* |
(a) Clear the DTCs.
Click here
(b) Recheck for DTCs.
Body Electrical > Main Body > Trouble Codes| Result | Proceed to |
|---|---|
| DTC B1243 is not output | A |
| DTC B1243 is output | B |
| B | | GO TO DIAGNOSTIC TROUBLE CODE CHART |
|
| 8. | PROBLEM SYMPTOMS TABLE |
(a) Refer to Problem Symptoms Table.
Click here
| Result | Proceed to |
|---|---|
| Fault is not listed in Problem Symptoms Table | A |
| Fault is listed in Problem Symptoms Table | B |
| B | | GO TO STEP 10 |
|
| 9. | OVERALL ANALYSIS AND TROUBLESHOOTING* |
(a) Terminals of ECU
Click here
(b) Data List / Active Test
Click here
(c) Operation Check
Click here
(d) Inspection
|
| 10. | REPAIR OR REPLACE |
|
| 11. | CONFIRMATION TEST |
| NEXT | | END |
System Diagram
Customize ParametersLexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Heated Steering Wheel Controller: Components
COMPONENTS ILLUSTRATION *1 CRUISE CONTROL MAIN SWITCH *2 SHIFT PADDLE SWITCH (TRANSMISSION SHIFT SWITCH ASSEMBLY) *3 STEERING PAD SWITCH ASSEMBLY *4 STEERING VIBRATION AND HEATER ECU N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part ★ Precoated Part ...
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Air Conditioning System: Air Conditioning Compressor Magnetic Clutch Circuit
DESCRIPTION When the air conditioning amplifier assembly is turned on, a magnetic clutch on signal is sent from the MGC terminal of the air conditioning amplifier assembly. Then, the semiconductor pwr integration ECU turns on to operate the magnetic clutch assembly. WIRING DIAGRAM CAUTION / NOTICE ...