Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual: Removal

Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual / Vehicle Interior / Supplemental Restraint Systems / Front Airbag Sensor / Removal

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front airbag sensor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replacement Part or Procedure

Necessary Procedures

Effects / Inoperative when not performed

Link

Front bumper assembly

Front television camera view adjustment

Panoramic view monitor system

for Initialization

for Calibration

Front bumper assembly (w/ Intelligent clearance sonar system)
  • Ultrasonic sensor detection angle
  • Ultrasonic sensor detection angle registration
  • Intelligent clearance sonar system
  • Intuitive parking assist system (w/ Intelligent Clearance Sonar System)

Disconnect cable from negative battery terminal

Memorize steering angle neutral point

Lane control system

Pre-collision system

Intelligent clearance sonar system*1

Lighting system (w/ Automatic Headlight Beam Level Control System)

Parking assist monitor system

Panoramic view monitor system

Initialize back door lock

Power door lock control system

Reset back door close position

Power back door system

*1: When performing learning using the Techstream.

Click here

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing.

Click here

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here

3. REMOVE FRONT BUMPER ASSEMBLY

Click here

4. DISCONNECT FRONT FENDER REINFORCEMENT SUB-ASSEMBLY TOP

Click here

5. REMOVE HEADLIGHT ASSEMBLY

Click here

6. REMOVE FRONT AIRBAG SENSOR

(a) Check that the engine switch is off.

(b) Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(c) Disconnect the connector from the front airbag sensor.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.

(1) Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

*a

White Housing Lock

*b

Yellow CPA

*c

Connector lock is released

-

-

(2) Push down the white housing lock again and disconnect the connector.

NOTICE:

Do not push down the part (A) shown in the illustration when disconnecting the connector.

(d) Remove the bolt and front airbag sensor.

NOTICE:

Loosen the bolt while holding the front airbag sensor because the front airbag sensor pin (stopper) is easily damaged.

(e) After disconnecting the connector, check that the position of the white housing lock is as shown in the illustration.

*a

Incorrect

*b

Correct
    On-vehicle Inspection
    ON-VEHICLE INSPECTION CAUTION / NOTICE / HINT CAUTION: Be sure to correctly follow the removal and installation procedures for the front airbag sensors. PROCEDURE 1. INSPECT FRONT AIRBAG SENSOR (for V ...

    Front Passenger Airbag Assembly
    ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Front Axle Hub: Components
    COMPONENTS ILLUSTRATION *A w/o AVS *B w/ AVS *1 FRONT AXLE ASSEMBLY *2 FRONT AXLE SHAFT NUT *3 FRONT DISC *4 FRONT DISC BRAKE CALIPER ASSEMBLY *5 FRONT DRIVE SHAFT ASSEMBLY *6 FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY *7 FRONT SPEED SENSOR *8 TIE ...

    Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Dynamic Torque Control Awd System: ABS Malfunction (C1296)
    DESCRIPTION If a malfunction in the speed sensor signal circuit or acceleration sensor (airbag sensor assembly*1 or yaw rate sensor assembly*2) circuit is detected, the 4WD ECU assembly stores this DTC. The airbag sensor assembly has a built-in acceleration sensor.*1 DTC No. Detection Item DT ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2026 Copyright www.lexusrx.net
    0.0094