Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual: Installation
INSTALLATION
CAUTION / NOTICE / HINT
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. INSTALL REAR AIRBAG SENSOR
(a) Check that the engine switch is off.
(b) Check that the cable is disconnected from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
.png)
(c) Before connecting the connector, check that the position of the white housing lock is as shown in the illustration.
.png)
| *a | Correct | *b | Incorrect |
(d) Engage the claw and install the rear airbag sensor with the bolt.
Torque:
9.0 N·m {92 kgf·cm, 80 in·lbf}
NOTICE:
- If the rear airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
- When installing the rear airbag sensor, make sure that the SRS wiring does not interfere with or is not pinched between other parts.
- Make sure that the rear airbag sensor claw is securely inserted into the body hole.
(e) Connect the connector to the rear airbag sensor.
.png)
| *a | White Housing Lock | *b | Connect |
NOTICE:
When connecting any airbag connector, take care not to damage the airbag wire harness.
HINT:
- Be sure to connect the connector until it is locked (when locking, make sure that a click sound can be heard).
- When the connector is locked, the white housing lock will slide. Do not hold the white housing lock or the part (A) as it may result in an insecure connection.
(f) Check that there is no looseness in the installed parts of the rear airbag sensor.
2. INSTALL REAR SEAT SIDE GARNISH
Click here .gif)
3. INSTALL UPPER QUARTER TRIM PAD
Click here
4. INSTALL REAR DOOR SCUFF PLATE
Click here
5. INSTALL REAR SEAT ASSEMBLY
for LH Side: Click here
for RH Side: Click here
On-vehicle Inspection
ON-VEHICLE INSPECTION CAUTION / NOTICE / HINT CAUTION: Be sure to correctly follow the removal and installation procedures for the rear airbag sensors. PROCEDURE 1. INSPECT REAR AIRBAG SENSOR (for Veh ...
Removal
REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the re ...
Other materials:
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Heated Steering Wheel System: System Description
SYSTEM DESCRIPTION HEATED STEERING WHEEL SYSTEM (a) The heated steering wheel system heats the steering wheel assembly when the steering heater switch (Integration control and panel assembly) is operated. (b) The heated steering wheel system uses a thermistor inside of the steering wheel assembly to ...
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Height Control Sensor: Inspection
INSPECTION PROCEDURE 1. INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH (a) Connect 3 dry cell batteries (1.5 V) in series. NOTICE: Do not use rechargeable batteries as they may not output a voltage of 1.5 V. *a Component without harness connected (Rear Height Control Sensor Sub-assembly RH ...
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual
- For your information
- Pictorial index
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Lexus Display Audio system
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual
0.0181