Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual: Inspection

Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual / Drivetrain / U881f (automatic Transmission / Transaxle) / Shift Lever / Inspection

INSPECTION

PROCEDURE

1. INSPECT SHIFT LOCK CONTROL ECU

HINT:

If the results of the following inspections are as specified but a malfunction has occurred, replace the transmission floor shift assembly.

(a) Inspect wire harness:

(1) Disconnect the shift lock control ECU connector.

(2) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

4 (STP) - Body ground

Brake pedal depressed

11 to 14 V

Brake pedal released

Below 1 V

5 (IG) - Body ground

Engine switch on (IG)

11 to 14 V

Engine switch off

Below 1 V

If the result is not as specified, repair or replace the shift lock control ECU wire harness.

*a

Front view of wire harness connector

(to Shift Lock Control ECU)

(3) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 (E) - Body ground

Always

Below 1 Ω

If the result is not as specified, repair or replace the shift lock control ECU wire harness.

*a

Front view of wire harness connector

(to Shift Lock Control ECU)

(b) Inspect shift lock solenoid:

(1) Disconnect the shift lock solenoid connector.

(2) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

4 (P) - 3 (E2)

Shift lever in P

10 kΩ or higher

Shift lever not in P

Below 1 Ω

If the result is not as specified, replace the transmission floor shift assembly.

If the shift lock does not operate when the power source of the transmission floor shift assembly is normal and the resistance between body ground and the shift lock solenoid is as specified, replace the transmission floor shift assembly.

*a

Front view of wire harness connector

(to Shift Lock Solenoid)

(3) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 (SLS+) - 2 (SLS-)

Always

112 Ω

If the result is not as specified, replace the transmission floor shift assembly.

If the shift lock does not operate when the power source of the transmission floor shift assembly is normal and the resistance between body ground and the shift lock solenoid is as specified, replace the transmission floor shift assembly.

*a

Front view of wire harness connector

(to Shift Lock Solenoid)

2. INSPECT TRANSMISSION CONTROL SWITCH

(a) Disconnect the transmission control switch connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

4 (IG) - 5 (S)

Shift lever in M, "+" or "-"

Below 1 Ω

Shift lever not in M, "+" or "-"

10 kΩ or higher

3 (SFTU) - 2 (E)

Shift lever held in "+"

(Up-shift)

Below 1 Ω

Shift lever not held in "+"

10 kΩ or higher

1 (SFTD) - 2 (E)

Shift lever held in "-"

(Down-shift)

Below 1 Ω

Shift lever not held in "-"

10 kΩ or higher

If the result is not as specified, replace the transmission floor shift assembly.

*a

Component without harness connected

(Transmission Control Switch (Transmission Floor Shift Assembly))
    Removal
    REMOVAL PROCEDURE 1. SECURE VEHICLE (a) Fully apply the parking brake and chock a wheel. CAUTION: Make sure to apply the parking brake and chock a wheel before performing this procedure. If the v ...

    Reassembly
    REASSEMBLY PROCEDURE 1. INSTALL SHIFT POSITION INDICATOR (a) Install the shift position indicator and console box bracket to the upper console panel sub-assembly with the 2 screws. *1 ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Lin Communication System: Front Passenger Side Door ECU Communication Stop (B2322)
    DESCRIPTION This DTC is stored when LIN communication between the power window regulator motor assembly RH and main body ECU (multiplex network body ECU) stops for 10 seconds or more. DTC No. Detection Item DTC Detection Condition Trouble Area B2322 Front Passenger Side Door ECU Commu ...

    Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Generator (for 180 A Type): Disassembly
    DISASSEMBLY PROCEDURE 1. REMOVE GENERATOR PULLEY CAP (a) Using a screwdriver, remove the generator pulley cap from the generator pulley with clutch. NOTICE: Do not reuse the generator pulley cap. 2. REMOVE GENERATOR REAR END COVER (a) Remove the 3 nuts and generator rear end cover ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2026 Copyright www.lexusrx.net
    0.0138