INSTALLATION
PROCEDURE
1. INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 2)
(a) Apply engine oil to a new O-ring and install it to the camshaft timing oil control solenoid assembly as shown in the illustration. NOTICE: Do not damage the O-ring. |
|
(b) Apply adhesive to 2 or 3 threads of 2 new bolts. Adhesive: Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent |
|
(c) Install the camshaft timing oil control solenoid assembly to the timing chain cover assembly with the 2 bolts.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
NOTICE:
(d) Connect the camshaft timing oil control solenoid assembly connector.
2. INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
Click here
3. INSTALL NO. 2 ENGINE MOUNTING STAY RH
Click here
4. REMOVE ENGINE SUPPORT BRIDGE
for 2WD: Click here
for AWD: Click here
5. CONNECT NO. 1 RADIATOR HOSE
Click here
6. INSTALL BRAKE ACTUATOR ASSEMBLY
Click here
7. INSTALL WIRE HARNESS CLAMP BRACKET
for 2WD: Click here
for AWD: Click here
8. INSTALL FUEL PUMP PROTECTOR
Click here
9. INSTALL BATTERY BRACKET REINFORCEMENT
for 2WD: Click here
for AWD: Click here
10. INSTALL BATTERY CARRIER SUB-ASSEMBLY
for 2WD: Click here
for AWD: Click here
11. INSTALL BATTERY
for 2WD: Click here
for AWD: Click here
12. INSTALL INLET AIR CLEANER ASSEMBLY
Click here
13. INSTALL INTAKE AIR SURGE TANK ASSEMBLY
Click here
14. INSTALL ECM
Click here
15. INSTALL NO. 2 ENGINE UNDER COVER
Click here
16. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY
Click here
17. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
Click here
18. INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 2)
(a) Apply engine oil to a new O-ring and install it to the camshaft timing oil control solenoid assembly as shown in the illustration. NOTICE: Do not damage the O-ring. |
|
(b) Apply adhesive to 2 or 3 threads of 2 new bolts. Adhesive: Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent |
|
(c) Install the camshaft timing oil control solenoid assembly to the timing chain cover assembly with the 2 bolts.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
NOTICE:
(d) Connect the camshaft timing oil control solenoid assembly connector.
19. INSPECT FOR ENGINE OIL LEAK
Click here
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Rear Axle Carrier (for Awd): Removal
REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear axle carrier sub-assembly removal/installation are shown below. Necessary Procedures After Parts R ...
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Intake Manifold: Components
COMPONENTS ILLUSTRATION *A for TMMC Made *B except TMMC Made *1 VENTILATION HOSE *2 PURGE VALVE (PURGE VSV) *3 NO. 1 FUEL VAPOR FEED HOSE *4 NO. 2 SURGE TANK STAY *5 INTAKE AIR SURGE TANK ASSEMBLY *6 AIR SURGE TANK TO INTAKE MANIFOLD GASKET *7 VACUUM HOS ...