DATA LIST / ACTIVE TEST
DATA LIST
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Chassis / Lane Control / Data List.
(e) According to the display on the Techstream, read the Data List.
Chassis > Lane Control > Data List| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled | - | - | - | Cannot be used |
| Total Distance Traveled - Unit | - | - | - | Cannot be used |
| LDA Control | Lane control system control status | Prohibit or Permit | Prohibit: Control prohibited Permit: Control permitted | - |
| Turn Switch (Right) | Right turn signal switch status | OFF or ON | OFF: Right turn signal switch off ON: Right turn signal switch on | - |
| Turn Switch (Left) | Left turn signal switch status | OFF or ON | OFF: Left turn signal switch off ON: Left turn signal switch on | - |
| Vehicle Information (2WD/4WD) | - | - | - | Cannot be used |
| Vehicle Information (Conv/HV) | - | - | - | Cannot be used |
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
ACTIVE TEST
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus:
(1) for Lane Control: Chassis / Lane Control / Active Test.
(2) for Combination Meter: Body Electrical / Combination Meter / Active Test.
(e) According to the display on the Techstream, perform the Active Test.
Chassis > Lane Control > Active Test| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Meter Buzzer | Sounds the meter buzzer | Start or Stop | Perform this Active Test with the vehicle stopped and the engine switch on (IG). |
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Meter Display 1 | Multi-information display | OFF or All | - |
Freeze Frame Data
Fail-safe ChartLexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Meter / Gauge System: Engine Coolant Temperature Receiver Gauge Malfunction
DESCRIPTION In this circuit, the combination meter assembly receives engine coolant temperature signals from the ECM via CAN communication. The combination meter assembly displays the engine coolant temperature that is calculated based on the data received from the ECM. WIRING DIAGRAM CAUTION / NOT ...
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Seat Heater Switch (for Rear Side): Installation
INSTALLATION CAUTION / NOTICE / HINT CAUTION: Wear protective gloves. Sharp areas on the seat frame may injure your hands. PROCEDURE 1. INSTALL REFRESHING SEAT SWITCH (for Console Box) (a) Engage the 2 guides. (b) Install the refreshing seat switch with the 3 screws. 2. INSTALL CONSOLE REAR END PANE ...