Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual: AFS ECU Communication Stop Mode

Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual / Power Source & Network / Networking / Can Communication System / AFS ECU Communication Stop Mode

DESCRIPTION

Detection Item

Symptom

Trouble Area

AFS ECU Communication Stop Mode

Either condition is met:

  • "Headlight swivel (AFS)" is not displayed on the CAN Bus Check screen of the Techstream.

    Click here

  • Communication system DTCs (DTCs that start with U) that correspond to "AFS ECU Communication Stop Mode" in "DTC Combination Table" are output.

    Click here

  • Headlight ECU sub-assembly LH branch line or connector
  • Power source circuit of headlight ECU sub-assembly LH
  • Headlight ECU sub-assembly LH ground circuit
  • Headlight ECU sub-assembly LH

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  • After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
  • DTC check procedure: Turn the engine switch on (IG) and wait for at least 33 seconds.
  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

HINT:

  • Operating the engine switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

PROCEDURE

1.

CHECK FOR OPEN IN CAN BUS LINES (HEADLIGHT ECU SUB-ASSEMBLY LH BRANCH LINE)

(a) Disconnect the cable from the negative (-) battery terminal.

(b) Disconnect the A49 headlight ECU sub-assembly LH connector.

*a

Front view of wire harness connector

(to Headlight ECU Sub-assembly LH)

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A49-24 (CANH) - A49-23 (CANL)

Cable disconnected from negative (-) battery terminal

54 to 69 Ω
NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH)
OK

2.

CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A49-12 (GND) - Body ground

Cable disconnected from negative (-) battery terminal

Below 1 Ω

*a

Front view of wire harness connector

(to Headlight ECU Sub-assembly LH)

(b) Reconnect the cable to the negative (-) battery terminal.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

A49-4 (IG) - Body ground

Engine switch on (IG)

11 to 14 V
OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
    Suspension Control ECU Communication Stop Mode
    DESCRIPTION Detection Item Symptom Trouble Area Suspension Control ECU Communication Stop Mode Either condition is met: "Suspension Control (Air Suspension)" is not displayed on the CA ...

    4WD Control ECU Communication Stop Mode
    DESCRIPTION Detection Item Symptom Trouble Area 4WD Control ECU Communication Stop Mode Either condition is met: "Four Wheel Drive Control" is not displayed on the CAN Bus Check screen ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Steering Gear: Reassembly
    REASSEMBLY PROCEDURE 1. INSTALL NO. 2 STEERING RACK BOOT (a) Apply lithium soap base glycol grease to the inside of the small opening of a new No. 2 steering rack boot. Lithium Soap Base Glycol Grease (b) Install the No. 2 steering rack boot to the groove on the rack housing. NOTICE: Be ...

    Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Rear Seat Side Airbag Assembly (for Captain Seat Type): Installation
    INSTALLATION PROCEDURE 1. INSTALL REAR SEAT AIRBAG ASSEMBLY (a) Install the rear seat airbag assembly with 2 new nuts. Torque: 5.5 N·m {56 kgf·cm, 49 in·lbf} NOTICE: Do not reuse the nuts. Make sure that the rear seatback frame sub-assembly is not deformed. If it is deformed, replace it wit ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2026 Copyright www.lexusrx.net
    0.0382