Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual: Suspension Control ECU Communication Stop Mode

Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual / Power Source & Network / Networking / Can Communication System / Suspension Control ECU Communication Stop Mode

DESCRIPTION

Detection Item

Symptom

Trouble Area

Suspension Control ECU Communication Stop Mode

Either condition is met:

  • "Suspension Control (Air Suspension)" is not displayed on the CAN Bus Check screen of the Techstream.

    Click here

  • Communication system DTCs (DTCs that start with U) that correspond to "Suspension Control ECU Communication Stop Mode" in "DTC Combination Table" are output.

    Click here

  • Absorber control ECU branch line or connector
  • Power source circuit of absorber control ECU
  • Absorber control ECU ground circuit
  • Absorber control ECU

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  • After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
  • DTC check procedure: Drive the vehicle at a speed of 30 km/h (19 mph) or more for 6 seconds or more.
  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

HINT:

  • Operating the engine switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

PROCEDURE

1.

CHECK FOR OPEN IN CAN BUS LINES (ABSORBER CONTROL ECU BRANCH LINE)

(a) Disconnect the cable from the negative (-) battery terminal.

(b) Disconnect the S51 absorber control ECU connector.

*a

Front view of wire harness connector

(to Absorber Control ECU)

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

S51-8 (CANH) - S51-7 (CANL)

Cable disconnected from negative (-) battery terminal

54 to 69 Ω
NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (ABSORBER CONTROL ECU)
OK

2.

CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

S51-4 (GND) - Body ground

Cable disconnected from negative (-) battery terminal

Below 1 Ω

*a

Front view of wire harness connector

(to Absorber Control ECU)

(b) Reconnect the cable to the negative (-) battery terminal.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

S51-1 (IGB) - Body ground

Engine switch on (IG)

11 to 14 V
OK

REPLACE ABSORBER CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
    Main Body ECU Communication Stop Mode
    DESCRIPTION Detection Item Symptom Trouble Area Main Body ECU Communication Stop Mode Either condition is met: "Main Body" is not displayed on the CAN Bus Check screen of the Techstrea ...

    AFS ECU Communication Stop Mode
    DESCRIPTION Detection Item Symptom Trouble Area AFS ECU Communication Stop Mode Either condition is met: "Headlight swivel (AFS)" is not displayed on the CAN Bus Check screen of the Te ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Windshield Outside Moulding: Installation
    INSTALLATION CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The following procedure is for the LH side. PROCEDURE 1. INSTALL NO. 3 WINDSHIELD OUTSIDE MOULDING CLIP HINT: Perform the following procedure only when replacement of a No. 3 windshield outside mou ...

    Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Air Cooled Oil Cooler: Installation
    INSTALLATION PROCEDURE 1. INSTALL OIL COOLER BRACKET HINT: Perform this procedure only when replacement of the oil cooler bracket is necessary. (a) Install the oil cooler bracket to the vehicle body with the bolt and nut. Torque: 5.5 N·m {56 kgf·cm, 49 in·lbf} NOTICE: Tightening order: Tempor ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2026 Copyright www.lexusrx.net
    0.0112