Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual: Millimeter Wave Radar Sensor Communication Stop Mode

Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual / Power Source & Network / Networking / Can Communication System / Millimeter Wave Radar Sensor Communication Stop Mode

DESCRIPTION

Detection Item

Symptom

Trouble Area

Millimeter Wave Radar Sensor Communication Stop Mode

Either condition is met:

  • "Front Radar" is not displayed on the CAN Bus Check screen of the Techstream.

    Click here

  • Communication system DTCs (DTCs that start with U) that correspond to "Millimeter Wave Radar Sensor Communication Stop Mode" in "DTC Combination Table" are output.

    Click here

  • Millimeter wave radar sensor assembly branch line or connector
  • Power source circuit of millimeter wave radar sensor assembly
  • Millimeter wave radar sensor assembly ground circuit
  • Millimeter wave radar sensor assembly

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  • After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
  • DTC check procedure: Drive the vehicle at a speed of 36 km/h (22 mph) or more for 7 seconds or more.
  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

HINT:

  • Operating the engine switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

PROCEDURE

1.

CHECK FOR OPEN IN CAN BUS LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY BRANCH LINE)

(a) Disconnect the cable from the negative (-) battery terminal.

(b) Disconnect the A70 millimeter wave radar sensor assembly connector.

*a

Front view of wire harness connector

(to Millimeter Wave Radar Sensor Assembly)

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A70-3 (CA2H) - A70-2 (CA2L)

Cable disconnected from negative (-) battery terminal

54 to 69 Ω
NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
OK

2.

CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A70-1 (SGND) - Body ground

Cable disconnected from negative (-) battery terminal

Below 1 Ω

*a

Front view of wire harness connector

(to Millimeter Wave Radar Sensor Assembly)

(b) Reconnect the cable to the negative (-) battery terminal.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

A70-8 (IGB) - Body ground

Engine switch on (IG)

11 to 14 V
OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
    DCM Communication Stop Mode
    DESCRIPTION Detection Item Symptom Trouble Area DCM Communication Stop Mode Either condition is met: "DCM" is not displayed on the CAN Bus Check screen of the Techstream. Click here ...

    Rear Television Camera Communication Stop Mode
    DESCRIPTION Detection Item Symptom Trouble Area Rear Television Camera Communication Stop Mode Either condition is met: "Parking Assist Monitor System" is not displayed on the CAN Bus ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Combination Meter: Disassembly
    DISASSEMBLY PROCEDURE 1. REMOVE COMBINATION METER GLASS (for Optitron Meter Type) (a) Disengage the 8 claws to remove the combination meter glass. 2. REMOVE COMBINATION METER GLASS (for TFT Meter Type) (a) Disengage the 9 claws to remove the combination meter glass. ...

    Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Rear Differential Carrier Oil Seal: Components
    COMPONENTS ILLUSTRATION *1 DIAPHRAGM OIL SEAL *2 ELECTRO MAGNETIC CONTROL COUPLING SUB-ASSEMBLY *3 ELECTRO MAGNETIC CONTROL COUPLING WIRE HARNESS *4 TRANSMISSION COUPLING CONICAL SPRING WASHER *5 TRANSMISSION COUPLING SPACER *6 REAR DIFFERENTIAL DRAIN PLUG *7 DIFF ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2026 Copyright www.lexusrx.net
    0.0124