Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual: Rear Television Camera Communication Stop Mode

Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual / Power Source & Network / Networking / Can Communication System / Rear Television Camera Communication Stop Mode

DESCRIPTION

Detection Item

Symptom

Trouble Area

Rear Television Camera Communication Stop Mode

Either condition is met:

  • "Parking Assist Monitor System" is not displayed on the CAN Bus Check screen of the Techstream.

    Click here

  • Communication system DTCs (DTCs that start with U) that correspond to "Rear Television Camera Communication Stop Mode" in "DTC Combination Table" are output.

    Click here

  • Rear television camera assembly branch line or connector
  • Power source circuit of rear television camera assembly
  • Rear television camera assembly ground circuit
  • Rear television camera assembly

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  • After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
  • DTC check procedure: Turn the engine switch on (IG) and wait for at least 20 seconds.
  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

    Click here

HINT:

  • Operating the engine switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

PROCEDURE

1.

CHECK FOR OPEN IN CAN BUS LINES (REAR TELEVISION CAMERA ASSEMBLY BRANCH LINE)

(a) Disconnect the cable from the negative (-) battery terminal.

(b) Disconnect the Z11 rear television camera assembly connector.

*a

Front view of wire harness connector

(to Rear Television Camera Assembly)

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Z11-4 (CANH) - Z11-1 (CANL)

Cable disconnected from negative (-) battery terminal

54 to 69 Ω
NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY)
OK

2.

CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Z11-5 (CGND) - Body ground

Cable disconnected from negative (-) battery terminal

Below 1 Ω

*a

Front view of wire harness connector

(to Rear Television Camera Assembly)

(b) Reconnect the cable to the negative (-) battery terminal.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

Z11-6 (CB+) - Body ground

Engine switch on (ACC)

5.5 to 7.05 V
OK

REPLACE REAR TELEVISION CAMERA ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
    Millimeter Wave Radar Sensor Communication Stop Mode
    DESCRIPTION Detection Item Symptom Trouble Area Millimeter Wave Radar Sensor Communication Stop Mode Either condition is met: "Front Radar" is not displayed on the CAN Bus Check screen ...

    Restraints Occupant Classification System Module Communication Stop Mode
    DESCRIPTION Detection Item Symptom Trouble Area Restraints Occupant Classification System Module Communication Stop Mode Either condition is met: "Occupant Detection" is not displayed ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Rear Spoiler: Disassembly
    DISASSEMBLY PROCEDURE 1. REMOVE NO. 1 REAR SPOILER PROTECTOR (except TMMC Made) (a) Remove the 5 No. 1 rear spoiler protectors. 2. REMOVE NO. 2 REAR SPOILER PROTECTOR (except TMMC Made) (a) Remove the 3 No. 2 rear spoiler protectors. 3. REMOVE REAR SPOILER SEAL (a) R ...

    Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Power Window Control System: Jam Protection Function does not Operate
    DESCRIPTION This symptom may occur for any of the power windows. The jam protection function operates within a specified range during the manual up or auto up operation. CAUTION / NOTICE / HINT NOTICE: If a power window regulator motor assembly has been replaced with a new one, initialize the pow ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2026 Copyright www.lexusrx.net
    0.0099