Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual: Removal

Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual / Vehicle Exterior / Exterior Panels / Trim / Rear Door Belt Moulding / Removal

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear door belt moulding removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed
*1: When performing learning using the Techstream. Click here
Disconnect cable from negative (-) battery terminal	Memorize steering angle neutral point	Lane Control System
		Pre-collision System
		Intelligent Clearance Sonar System*1
		Parking Assist Monitor System
		Panoramic View Monitor System
		Lighting System (w/ Automatic Headlight Beam Level Control System)
	Initialize back door lock	Power Door Lock Control System
	Reset back door close position	Power Back Door System (w/ Outside Door Control Switch)

HINT:

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here

3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

Click here

4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

Click here

5. REMOVE REAR DOOR ARMREST COVER

Click here

6. REMOVE COURTESY LIGHT ASSEMBLY

Click here

7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

Click here

8. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP

Click here

9. REMOVE REAR DOOR NO. 2 TRIM BRACKET

Click here

10. REMOVE REAR DOOR SERVICE HOLE COVER

Click here

11. REMOVE REAR DOOR GLASS RUN

Click here

12. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

Click here

13. DISCONNECT REAR DOOR WEATHERSTRIP

Click here

14. REMOVE REAR DOOR REAR GUIDE SEAL

Click here

15. REMOVE REAR DOOR GLASS SUB-ASSEMBLY

Click here

16. REMOVE REAR DOOR BELT MOULDING ASSEMBLY

(a) Apply protective tape around the rear door belt moulding assembly.

Protective Tape

(b) Disengage the 8 claws as shown in the illustration to remove the rear door belt moulding assembly.

Remove in this Direction

Installation

INSTALLATION CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The following procedure is for the LH side. PROCEDURE 1. INSTALL REAR DOOR BELT MOULDING ASSEMBLY ...

Rear Door Outside Moulding

...

Other materials:

Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Audio And Visual System (for 8 Inch Display): Freeze Frame Data
FREEZE FRAME DATA CHECK FREEZE FRAME DATA (a) Connect the Techstream to the DLC3. (b) Turn the engine switch on (IG). (c) Turn the Techstream on. (d) Enter the following menus: Body Electrical / Navigation System / Trouble Codes. Body Electrical > Navigation System > Trouble Codes (e) Select a ...

Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Camshaft Oil Control Solenoid (for Bank 1): Installation
INSTALLATION CAUTION / NOTICE / HINT CAUTION: The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter. To prevent burns, do not t ...

Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual: Removal

Installation

Rear Door Outside Moulding

Other materials:

Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual