Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual: Removal
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during roof drip side finish moulding removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced| Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
|
*1: When performing learning using the Techstream.
Click here | |||
| Disconnect cable from negative (-) battery terminal | Memorize steering angle neutral point | Lane Control System | |
| Pre-collision System | |||
| Intelligent Clearance Sonar System*1 | |||
| Parking Assist Monitor System | | ||
| Panoramic View Monitor System | | ||
| Lighting System (w/ Automatic Headlight Beam Level Control System) | | ||
| Initialize back door lock | Power Door Lock Control System | | |
| Reset back door close position | Power Back Door System (w/ Outside Door Control Switch) | | |
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
.png)
Click here .gif)
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. REMOVE CENTER ROOF DRIP SIDE FINISH MOULDING (w/o Roof Rack)
(a) Apply protective tape around the center roof drip side finish moulding.
.png) | Protective Tape | - | - |
(b) Using a moulding remover, disengage the 2 clips and remove the center roof drip side finish moulding.
2. REMOVE ROOF RACK ASSEMBLY (w/ Roof Rack)
w/o Rear No. 2 Seat: Click here
w/ Rear No. 2 Seat: Click here
3. REMOVE ROOF DRIP SIDE FINISH MOULDING (w/ Roof Rack)
(a) except Panoramic Moon Roof:
(1) Apply protective tape around the roof drip side finish moulding.
| | Protective Tape |
| (2) Using a moulding remover, disengage the clip and remove the roof drip side finish moulding. |
|
4. REMOVE REAR ROOF DRIP SIDE FINISH MOULDING (w/ Roof Rack)
(a) Apply protective tape around the rear roof drip side finish moulding.
| | Protective Tape |
| (b) Using a moulding remover, disengage the clip and remove the rear roof drip side finish moulding. |
|
Components
COMPONENTS ILLUSTRATION *A w/ Roof Rack *B w/o Roof Rack *C except Panoramic Moon Roof - - *1 CENTER ROOF DRIP SIDE FINISH MOULDING *2 REAR ROOF DRIP SIDE FINISH MOULDING ...
Installation
INSTALLATION CAUTION / NOTICE / HINT HINT:
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
PROCEDURE 1. INSTALL ROOF DRIP SIDE FINISH MOULDING C ...
Other materials:
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Audio And Visual System (for 12.3 Inch Display): Disc cannot be Ejected
CAUTION / NOTICE / HINT NOTICE: Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System. Click here PROCEDURE 1. CHECK OPERATION (a) Press the d ...
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Air Conditioning System: Evaporator Temperature Circuit (B1417/17)
DESCRIPTION The No. 2 air conditioning harness assembly is installed on the evaporator in the rear air conditioner unit to detect the temperature of the cooled air that has passed through the evaporator, which is used to control the air conditioning system. It sends signals to the air conditioning a ...
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual
- For your information
- Pictorial index
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Lexus Display Audio system
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual
0.0115