CAUTION / NOTICE / HINT
HINT:
PROCEDURE
1. | VEHICLE BROUGHT TO WORKSHOP |
|
2. | CUSTOMER PROBLEM ANALYSIS |
HINT:
What | Vehicle model, system name |
When | Date, time, occurrence frequency |
Where | Road conditions |
Under what conditions? | Driving conditions, weather conditions |
How did it happen? | Problem symptoms |
|
3. | PRE-CHECK |
(a) Measure the battery voltage.
Standard Voltage:
11 to 14 V
If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.
(b) Check the fuses and relays.
(c) Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.
|
4. | INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM* |
(a) Using the Techstream, check for CAN communication system DTCs.
Click here
Result | Proceed to |
---|---|
CAN DTCs are not output | A |
CAN DTCs are output | B |
B | GO TO CAN COMMUNICATION SYSTEM |
|
5. | INSPECT COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM* |
(a) Using the Techstream, check for LIN communication system DTCs.
Click here
Result | Proceed to |
---|---|
LIN DTCs are not output | A |
LIN DTCs are output | B |
B | GO TO LIN COMMUNICATION SYSTEM |
|
6. | CHECK FOR DTC* |
(a) Check for DTCs and make a note of any codes that are output.
Click here
Body Electrical > Master Switch > Trouble Codes Body Electrical > D-Door Motor > Trouble Codes Body Electrical > P-Door Motor > Trouble Codes Body Electrical > RL-Door Motor > Trouble Codes Body Electrical > RR-Door Motor > Trouble Codes(b) Clear the DTCs.
Body Electrical > Master Switch > Clear DTCs Body Electrical > D-Door Motor > Clear DTCs Body Electrical > P-Door Motor > Clear DTCs Body Electrical > RL-Door Motor > Clear DTCs Body Electrical > RR-Door Motor > Clear DTCs(c) Recheck for DTCs.
Body Electrical > Master Switch > Trouble Codes Body Electrical > D-Door Motor > Trouble Codes Body Electrical > P-Door Motor > Trouble Codes Body Electrical > RL-Door Motor > Trouble Codes Body Electrical > RR-Door Motor > Trouble Codes Result | Proceed to |
---|---|
DTCs are not output | A |
DTCs are output | B |
B | GO TO DIAGNOSTIC TROUBLE CODE CHART |
|
7. | PROBLEM SYMPTOMS TABLE |
(a) Refer to Problem Symptoms Table.
Click here
Result | Proceed to |
---|---|
Fault is not listed in problem symptoms table | A |
Fault is listed in problem symptoms table | B |
B | GO TO STEP 9 |
|
8. | OVERALL ANALYSIS AND TROUBLESHOOTING* |
(a) Operation Check
Click here
(b) Terminals of ECU
Click here
(c) Data List / Active Test
Click here
(d) Fail-safe Chart
Click here
(e) Inspection
|
9. | ADJUST, REPAIR OR REPLACE |
(a) Check if any of the door window regulator sub-assemblies, power window regulator motor assemblies, door glass or door glass runs have been removed and reinstalled.
Result | Proceed to |
---|---|
Any of the door window regulator sub-assemblies, power window regulator motor assemblies, door glass or door glass runs have been removed and reinstalled. | A |
The door window regulator sub-assemblies, power window regulator motor assemblies, door glass or door glass runs have not been removed and reinstalled. | B |
B | GO TO STEP 11 |
|
10. | INITIALIZE POWER WINDOW CONTROL SYSTEM |
(a) If any of the door window regulator sub-assemblies, power window regulator motor assemblies, door glass or door glass runs have been removed and reinstalled, perform "Initialize Power Window Control System" for the applicable door glass.
Click here
|
11. | CONFIRMATION TEST |
NEXT | END |
Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Lighting System (w/o Automatic Headlight Beam Level Control System): How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT HINT:
Use the following procedure to troubleshoot the lighting system.
*: Use the Techstream.
PROCEDURE 1. VEHICLE BROUGHT TO WORKSHOP
NEXT 2. CUSTOMER PROBLEM ANALYSIS HINT:
In troubleshooting, confirm that the problem symptoms h ...
Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Rear Axle Hub: Removal
REMOVAL CAUTION / NOTICE / HINT HINT:
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
PROCEDURE 1. REMOVE REAR WHEEL Click here 2. REMOVE REAR SUSPENSION ARM COVER Click here 3. REMOVE REAR AXLE SHAFT NUT (for AWD) (a) Using SST and a ...