REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front seatback heater removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced| Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here | |||
| Disconnect cable from negative battery terminal | Memorize steering angle neutral point | Lane Control System | |
| Pre-collision System | |||
| Intelligent Clearance Sonar System* | |||
| Parking Assist Monitor System | | ||
| Panoramic View Monitor System | | ||
| Lighting System (w/ Automatic Headlight Beam Level Control System) | | ||
| Initialize back door lock | Power Door Lock Control System | | |
| Reset back door close position | Power Back Door System (w/ Outside Door Control Switch) | | |
| Initialize position control ECU | Front Power Seat Control System (w/ Memory) | |
CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.
HINT:
PROCEDURE
1. REMOVE FRONT SEAT ASSEMBLY
Click here
2. DISCONNECT FRONT SEATBACK BOARD SUB-ASSEMBLY
Click here
3. REMOVE FRONT SEAT CUSHION SHIELD (for Standard Seat Type)
Click here
4. REMOVE INNER NO. 1 FRONT SEAT CUSHION SHIELD (for Standard Seat Type)
Click here
5. REMOVE INNER NO. 1 FRONT SEAT CUSHION SHIELD (for Sports Seat Type)
Click here
6. REMOVE FRONT SEAT CUSHION SHIELD (for Sports Seat Type)
Click here
7. REMOVE FRONT SEAT INNER CUSHION SHIELD
Click here
8. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY
Click here
9. REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY
Click here
10. REMOVE FRONT SEAT HEADREST SUPPORT
Click here
11. REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for Standard Seat Type)
Click here
12. REMOVE SEPARATE TYPE FRONT SEATBACK COVER (for Standard Seat Type)
| (a) Remove the 12 hog rings to remove the separate type front seatback cover from the separate type front seatback pad. |
|
13. REMOVE FRONT SEATBACK HEATER ASSEMBLY (for Standard Seat Type)
| (a) Remove the 12 tag pins and front seatback heater assembly from the separate type front seatback cover. |
|
14. REMOVE FRONT SEATBACK HEATER (FRONT SEATBACK PAD WITH COVER) (for Sports Seat Type)
HINT:
The front seatback heater cannot be removed from the front seatback pad with cover as they are a unit.
| (a) Remove the 2 nuts and disengage the 2 brackets. |
|
(b) Remove the front seatback heater (front seatback pad with cover).
Components
InspectionLexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Rear Differential Carrier Assembly: Disassembly
DISASSEMBLY CAUTION / NOTICE / HINT NOTICE:
Before installation, thoroughly clean and dry each part and then apply Toyota Genuine Differential gear oil LT SAE 75W-85 GL-5 or equivalent to them.
Do not use alkaline cleaner for aluminum or rubber parts and rear differential case bolts.
Do not c ...
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Can Communication System: Open in Bus 5 Main Bus Line
DESCRIPTION There may be an open circuit in one of the bus 5 main lines when the resistance between terminals 15 (CA5H) and 16 (CA5L) of the network gateway ECU is 70 Ω or higher. Symptom Trouble Area Resistance between terminals 15 (CA5H) and 16 (CA5L) of network gateway ECU is 70 Ω or h ...