REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear No. 1 seat assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced Replaced Part or Performed Procedure | Necessary Procedures | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
---|---|---|---|
Disconnect cable from negative battery terminal | Memorize steering angle neutral point | Lane Control System |
|
Pre-collision System | |||
Intelligent Clearance Sonar System*1 | |||
Parking Assist Monitor System |
| ||
Panoramic View Monitor System |
| ||
Lighting System (w/ Automatic Headlight Beam Level Control System) |
| ||
Initialize back door lock | Power Door Lock Control System |
| |
Reset back door close position | Power Back Door System (w/ Outside Door Control Switch) |
|
*1: When performing learning using the Techstream.
Click here
CAUTION:
Click here
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION:
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
3. REMOVE REAR SEAT HEADREST ASSEMBLY
(a) Remove the rear seat headrest assembly.
4. REMOVE REAR DOOR SCUFF PLATE LH
Click here
5. REMOVE SEAT INNER TRACK BRACKET COVER LH
(a) Operate the seat track adjusting handle and move the rear No. 1 seat assembly LH to the foremost position.
(b) Disengage the 8 clips and 2 guides, and remove the seat inner track bracket cover LH. | |
6. REMOVE REAR SEAT OUTER TRACK BRACKET COVER LH
(a) Disengage the 4 clips and guide, and remove the rear seat outer track bracket cover LH. | |
7. REMOVE REAR SEAT OUTER TRACK BRACKET COVER LH
(a) Operate the seat track adjusting handle and move the rear No. 1 seat assembly LH to the rearmost position.
(b) Disengage the 2 claws and 2 guides to remove the rear seat outer track bracket cover LH as shown in the illustration.
Place Hand Here | |
Remove in this Direction |
8. REMOVE REAR SEAT INNER TRACK BRACKET COVER LH
HINT:
Use the same procedure as for the rear seat outer track bracket cover LH.
9. REMOVE REAR NO. 1 SEAT ASSEMBLY LH
(a) Disconnect the rear seat airbag assembly connector.
NOTICE:
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
(1) Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)
*a | White Housing Lock |
*b | Yellow CPA |
Slide |
(2) Push down the white housing lock again and disconnect the connector.
NOTICE:
Do not push the part (A) shown in the illustration when disconnecting the connector.
(b) Disconnect the connector. | |
(c) Remove the 2 bolts. | |
(d) Operate the seat track adjusting handle and move the rear No. 1 seat assembly LH to the foremost position.
(e) Remove the 3 bolts. | |
(f) Disengage the 2 pins and remove the rear No. 1 seat assembly LH. NOTICE: Be careful not to damage the rear No. 1 seat assembly LH, vehicle body or vehicle interior. | |
Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Front Radar Sensor System: Front Radar Sensor Optical Axis Misalignment Malfunction (C1A1100)
DESCRIPTION The millimeter wave radar sensor assembly performs self-diagnosis to check for misalignment of its beam axis. If misalignment is detected, the millimeter wave radar sensor assembly stores DTC C1A1100. DTC No. Detection Item DTC Detection Condition Trouble Area C1A1100 Fron ...
Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Inner Rear View Mirror: Inspection
INSPECTION PROCEDURE 1. INSPECT INNER REAR VIEW MIRROR ASSEMBLY (a) Inspect the operation of the electrochromic inner rear view mirror assembly. *a Black Colored Tape *b Forward Sensor *c Bright *d Dark *e Battery *f EC Switch *g Component without harness connecte ...