Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual: Removal

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear seat cushion heater removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedures

Effect/Inoperative Function When Necessary Procedures are not Performed

Link

Disconnect cable from negative battery terminal

Memorize steering angle neutral point

Lane Control System

Pre-collision System

Intelligent Clearance Sonar System*1

Parking Assist Monitor System

Panoramic View Monitor System

Lighting System (w/ Automatic Headlight Beam Level Control System)

Initialize back door lock

Power Door Lock Control System

Reset back door close position

Power Back Door System (w/ Outside Door Control Switch)

*1: When performing learning using the Techstream.

Click here

CAUTION:

  • Be sure to read Precaution thoroughly before servicing.

    Click here

  • Wear protective gloves. Sharp areas on the parts may injure your hands.

PROCEDURE

1. REMOVE REAR SEAT ASSEMBLY LH (w/o Rear No. 2 Seat)

Click here

2. REMOVE REAR CENTER SEAT INNER BELT ASSEMBLY (w/o Rear No. 2 Seat)

Click here

3. REMOVE REAR SEAT COVER CAP LH (w/o Rear No. 2 Seat)

for Manual Seat:

Click here

4. REMOVE NO. 1 RECLINING ADJUSTER RELEASE HANDLE LH (w/o Rear No. 2 Seat)

for Manual Seat:

Click here

5. REMOVE POWER SEAT SWITCH ASSEMBLY (w/o Rear No. 2 Seat)

for Power Seat:

Click here

6. DISCONNECT SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD (w/o Rear No. 2 Seat)

Click here

7. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD (w/o Rear No. 2 Seat)

Click here

8. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER (w/o Rear No. 2 Seat)

Click here

9. REMOVE SEAT HEATER ASSEMBLY (w/o Rear No. 2 Seat)

(a) Remove the 14 tag pins and seat heater assembly from the separate type rear seat cushion cover.

10. REMOVE REAR NO. 1 SEAT ASSEMBLY LH (w/ Rear No. 2 Seat)

Click here

11. REMOVE REAR SEAT COVER CAP LH (w/ Rear No. 2 Seat)

Click here

12. REMOVE NO. 1 RECLINING ADJUSTER RELEASE HANDLE LH (w/ Rear No. 2 Seat)

Click here

13. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH (w/ Rear No. 2 Seat)

Click here

14. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD (w/ Rear No. 2 Seat)

Click here

15. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER (w/ Rear No. 2 Seat)

Click here

16. REMOVE SEAT HEATER ASSEMBLY (w/ Rear No. 2 Seat)

(a) Remove the 14 tag pins and seat heater assembly from the separate type rear seat cushion cover.

    Installation
    INSTALLATION CAUTION / NOTICE / HINT CAUTION: Wear protective gloves. Sharp areas on the seat frame may injure your hands. PROCEDURE 1. INSTALL SEAT HEATER ASSEMBLY (w/o Rear No. 2 Seat) (a) Install t ...

    Rear Seat Cushion Heater (for Captain Seat Type)
    ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Roof Headlining (w/o Rear No. 2 Seat): Disassembly
    DISASSEMBLY PROCEDURE 1. REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY Click here 2. REMOVE WASHER HOSE ASSEMBLY (a) Remove the washer hose assembly. *A for Standard Roof *B for Sliding Roof *C for Panoramic Moon Roof - - 3. REMOVE VANITY LIGHT ASSEMBLY HINT: Use the same procedu ...

    Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Steering Column Assembly: Installation
    INSTALLATION PROCEDURE 1. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD 2. INSTALL STEERING COLUMN ASSEMBLY NOTICE: Make sure that the wire harness is not interfering with the steering column assembly. (a) Install the steering column assembly with the bolt and 2 nuts. Torque: 36 N·m {367 kgf·cm, 27 ft ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2026 Copyright www.lexusrx.net
    0.0102