Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual: Removal

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear seat inner belt assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Disconnect cable from negative battery terminal

Memorize steering angle neutral point

Lane Control System

Pre-collision system

Intelligent clearance sonar system*1

Lighting system (w/ Automatic Headlight Beam Level Control System)

Parking assist monitor system

Panoramic view monitor system

Initialize back door lock

Power door lock control system

Reset back door close position

Power Back Door System (w/ Outside Door Control Switch)

*1: When performing learning using the Techstream.

Click here

CAUTION:

  • Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

    Click here

  • Wear protective gloves. Sharp areas on the parts may injure your hands.

NOTICE:

After the engine switch is turned off, the radio receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) battery terminal.

PROCEDURE

1. REMOVE REAR SEAT ASSEMBLY LH

Click here

2. REMOVE REAR CENTER SEAT INNER BELT ASSEMBLY

Click here

3. REMOVE REAR SEAT COVER CAP LH (for Manual Seat)

Click here

4. REMOVE NO. 1 RECLINING ADJUSTER RELEASE HANDLE LH (for Manual Seat)

Click here

5. REMOVE POWER SEAT SWITCH ASSEMBLY (for Power Seat)

Click here

6. DISCONNECT SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD

Click here

7. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD

Click here

8. REMOVE REAR SEAT INNER BELT ASSEMBLY LH

(a) Disengage each clamp.

(b) Remove the bolt and rear seat inner belt assembly LH.

    Components
    COMPONENTS ILLUSTRATION *A for Manual Seat *B for Power Seat *1 NO. 1 RECLINING ADJUSTER RELEASE HANDLE LH *2 POWER SEAT SWITCH ASSEMBLY *3 REAR CENTER SEAT INNER BELT ASSEMB ...

    Inspection
    INSPECTION PROCEDURE 1. INSPECT REAR SEAT INNER BELT ASSEMBLY LH (a) Measure the resistance according to the value(s) in the table below. Standard Resistance: Tester Connection Condition Sp ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Automatic Transaxle System: Shift Solenoid "A" Circuit Short to Ground (P075011)
    DESCRIPTION Changing gears is performed by the ECM turning the shift solenoid valves SL1, SL2, SL3, SL4, SL5, S1 and S2 on and off. If an open or short occurs in any of the shift solenoid valve circuits, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be driven. I ...

    Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Can Communication System: Parking Assist ECU Communication Stop Mode
    DESCRIPTION Detection Item Symptom Trouble Area Parking Assist ECU Communication Stop Mode Either condition is met: "Panoramic View Monitor" is not displayed on the CAN Bus Check screen of the Techstream. Click here Communication system DTCs (DTCs that start with U) that correspo ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2025 Copyright www.lexusrx.net
    0.014