DESCRIPTION
The front airbag sensor RH circuit consists of the airbag sensor assembly and front airbag sensor RH.
The front airbag sensor RH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbags, pretensioners and selectable force limiter should be deployed.
DTC B1610 is stored when a malfunction is detected in the front airbag sensor RH.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Test Mode / Check Mode |
|---|---|---|---|---|---|
| B1610 | Front Airbag Sensor (RH) |
|
| Comes on | Does not apply to test/check mode |
WIRING DIAGRAM
Click here
CAUTION / NOTICE / HINT
NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
PROCEDURE
| 1. | CHECK FRONT AIRBAG SENSOR RH |
| (a) Turn the engine switch off. |
|
(b) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Interchange the front airbag sensor RH with LH and connect the connectors.
(d) Connect the cable to the negative (-) battery terminal.
(e) Turn the engine switch on (IG), and wait for at least 60 seconds.
(f) Clear the DTCs stored in memory.
Body Electrical > SRS Airbag > Clear DTCs(g) Turn the engine switch off.
(h) Turn the engine switch on (IG), and wait for at least 60 seconds.
(i) Check for DTCs.
Body Electrical > SRS Airbag > Trouble CodesHINT:
Codes other than DTCs B1610 and B1615 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTCs B1610 and B1615 are not output. | A |
| DTC B1610 is output. | B |
| DTC B1615 is output. | C |
(j) Turn the engine switch off.
(k) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(l) Return the front airbag sensor RH and LH to their original positions and connect the connectors.
| A | | USE SIMULATION METHOD TO CHECK |
| B | | REPLACE AIRBAG SENSOR ASSEMBLY |
| C | | REPLACE FRONT AIRBAG SENSOR RH |
Airbag ECU Malfunction1 (B1160-B1167)
Front Airbag Sensor Lost Communication (RH) (B1612,B1613)Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Vacuum Warning Switch: Removal
REMOVAL PROCEDURE 1. REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY Click here 2. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY Click here 3. REMOVE VACUUM WARNING SWITCH ASSEMBLY (for TMC Made) (a) Disconnect the connector from the vacuum warning switch assembly. (b) Remove the vacuum w ...
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Washer Nozzle(for Rear Side): Installation
INSTALLATION PROCEDURE 1. INSTALL REAR WASHER NOZZLE (a) Engage the 2 claws to install the rear washer nozzle. (b) Connect the rear washer hose. 2. INSPECT REAR WASHER NOZZLE (w/o Rear No. 2 Seat) Click here 3. INSPECT REAR WASHER NOZZLE (w/ Rear No. 2 Seat) Click here 4. ADJUST REAR WASHER NOZZ ...