DESCRIPTION
The front airbag sensor LH circuit consists of the airbag sensor assembly and front airbag sensor LH.
The front airbag sensor LH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbags, pretensioners and selectable force limiter should be deployed.
DTC B1615 is stored when a malfunction is detected in the front airbag sensor LH.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Test Mode / Check Mode |
|---|---|---|---|---|---|
| B1615 | Front Airbag Sensor (LH) |
|
| Comes on | Does not apply to test/check mode |
WIRING DIAGRAM
Click here
CAUTION / NOTICE / HINT
NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
PROCEDURE
| 1. | CHECK FRONT AIRBAG SENSOR LH |
| (a) Turn the engine switch off. |
|
(b) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Interchange the front airbag sensor LH with RH and connect the connectors.
(d) Connect the cable to the negative (-) battery terminal.
(e) Turn the engine switch on (IG), and wait for at least 60 seconds.
(f) Clear the DTCs stored in memory.
Body Electrical > SRS Airbag > Clear DTCs(g) Turn the engine switch off.
(h) Turn the engine switch on (IG), and wait for at least 60 seconds.
(i) Check for DTCs.
Body Electrical > SRS Airbag > Trouble CodesHINT:
Codes other than DTCs B1610 and B1615 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTCs B1610 and B1615 are not output. | A |
| DTC B1615 is output. | B |
| DTC B1610 is output. | C |
(j) Turn the engine switch off.
(k) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(l) Return the front airbag sensor LH and RH to their original positions and connect the connectors.
| A | | USE SIMULATION METHOD TO CHECK |
| B | | REPLACE AIRBAG SENSOR ASSEMBLY |
| C | | REPLACE FRONT AIRBAG SENSOR LH |
Front Airbag Sensor Lost Communication (RH) (B1612,B1613)
Front Airbag Sensor Lost Communication (LH) (B1617,B1618)Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Power Tilt And Power Telescopic Steering Column System: ECU Power Source Circuit Malfunction (B2620)
DESCRIPTION The ECU power source circuit supplies positive (+) voltage to the multiplex tilt and telescopic ECU. DTC No. Detection Item DTC Detection Condition Trouble Area B2620 ECU Power Source Circuit Malfunction The voltage of the ECU power source drops to 8 V or less and this c ...
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Rear Drive Shaft Assembly: Installation
INSTALLATION CAUTION / NOTICE / HINT HINT:
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
PROCEDURE 1. INSTALL REAR DRIVE SHAFT SNAP RING (a) Install a new rear drive shaft snap ring. NOTICE: Face the end gap of the rear drive shaft snap ring ...