Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual: Installation

INSTALLATION

CAUTION / NOTICE / HINT

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY

NOTICE:

When installing a curtain shield airbag assembly, have assistants hold it to prevent it from bending.

(a) Check that the engine switch is off.

(b) Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(c) Insert the 2 hooks, install the curtain shield airbag assembly with 8 new bolts, 2 new spacers, each new clip (A) with pin and clip (B) with pin, and engage the 5 clips (C) in the order shown in the illustration.

Torque:

9.8 N·m {100 kgf·cm, 87 in·lbf}

NOTICE:

Do not twist the curtain shield airbag assembly when installing it.

HINT:

Engage the 2 claws to install each new clip (A) and clip (B).

*1

Pin

*2

Spacer

*a

Clip (A)

*b

Clip (B)

*c

Clip (C)

*d

Clip (A) or Clip (B)

*e

Spacer Location

*f

Needle Nose Pliers No. 2

(d) Using a needle nose pliers No. 2 or equivalent, push the 6 pins into each clip (A) and clip (B).

NOTICE:

  • Do not damage the pins.
  • Make sure that the pins of each clip (A) and clip (B) are pushed in firmly.

(e) Connect the airbag connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.

*a

Airbag Connector

*b

Airbag Connector Lock

(f) Push in the airbag connector lock to install the airbag connector.

2. INSTALL ROOF HEADLINING ASSEMBLY

Click here

3. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here

4. PERFORM DIAGNOSTIC SYSTEM CHECK

Click here

5. INSPECT SRS WARNING LIGHT

Click here

    Removal
    REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the cu ...

    Disposal
    DISPOSAL CAUTION / NOTICE / HINT CAUTION: Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disp ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Panoramic View Monitor System: Front Wheel Speed Sensor Malfunction (C164D)
    DESCRIPTION This DTC is stored when the parking assist ECU receives a wheel speed sensor (front speed sensor RH or front speed sensor LH, rear speed sensor RH or rear speed sensor LH) abnormality signal from the vehicle stability control system via CAN communication. DTC No. Detection Item DT ...

    Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Transfer Assembly: Installation
    INSTALLATION PROCEDURE 1. INSTALL TRANSFER ASSEMBLY (a) Install 4 new transfer and transaxle setting stud bolts to the automatic transaxle assembly positions shown in the illustration. *a 69 mm (2.72 in.) *b 49 mm (1.93 in.) *c 22 mm (0.866 in.) - - Torque: 39.2 N·m {400 kgf ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2025 Copyright www.lexusrx.net
    0.0148