Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual: Installation
INSTALLATION
CAUTION / NOTICE / HINT
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. INSTALL FRONT AIRBAG SENSOR
(a) Check that the engine switch is off.
(b) Check that the cable is disconnected from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
.png)
(c) Before connecting the connector, check that the position of the white housing lock is as shown in the illustration.
| *a | Incorrect | *b | Correct |
(d) Insert the front airbag sensor pin (stopper) into the body hole and install the front airbag sensor to the vehicle body with the bolt.
Torque:
9.0 N·m {92 kgf·cm, 80 in·lbf}
NOTICE:
- If the front airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
- When installing the front airbag sensor, make sure that the SRS wiring does not interfere with or is not pinched between other parts.
- Make sure that the front airbag sensor pin (stopper) is securely inserted into the body hole.
- Tighten the bolt while holding the front airbag sensor because the front airbag sensor pin (stopper) is easily damaged.
(e) Connect the connector to the front airbag sensor.
| *a | White Housing Lock | *b | Connection is completed |
NOTICE:
When connecting any airbag connector, take care not to damage the airbag wire harness.
HINT:
- Be sure to connect the connector until it is locked (when locking, make sure that a click sound can be heard).
- When the connector is locked, the white housing lock will slide. Do not hold the white housing lock or the part (A) as it may result in an insecure connection.
(f) Check that there is no looseness in the installed parts of the front airbag sensor.
2. INSTALL HEADLIGHT ASSEMBLY
Click here .gif)
3. INSTALL FRONT FENDER REINFORCEMENT SUB-ASSEMBLY TOP
Click here
4. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
5. INSTALL FRONT BUMPER ASSEMBLY
Click here
6. INSPECT AND ADJUST HEADLIGHT AIMING
Click here
7. PERFORM DIAGNOSTIC SYSTEM CHECK
Click here
8. INSPECT SRS WARNING LIGHT
Click here
Components
COMPONENTS ILLUSTRATION *1 FRONT AIRBAG SENSOR *2 FRONT FENDER REINFORCEMENT SUB-ASSEMBLY TOP *3 HEADLIGHT ASSEMBLY *4 CENTER HOOD CUSHION Tightening torque for "Major areas ...
On-vehicle Inspection
ON-VEHICLE INSPECTION CAUTION / NOTICE / HINT CAUTION: Be sure to correctly follow the removal and installation procedures for the front airbag sensors. PROCEDURE 1. INSPECT FRONT AIRBAG SENSOR (for V ...
Other materials:
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Mass Air Flow Meter: Installation
INSTALLATION PROCEDURE 1. INSTALL MASS AIR FLOW METER SUB-ASSEMBLY HINT: Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly. Click here (a) Install the mass air flow meter sub-assembly to the air cleaner cap sub-assembly with the 2 screws. NOTICE:
If the mas ...
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Power Window Control System: Auto Down Operation does not Fully Open Power Window (Catch Protection Function is Activated)
DESCRIPTION If a door glass does not slide smoothly or a power window regulator motor assembly or door window regulator sub-assembly does not operate smoothly, the catch protection function may be triggered automatically, resulting in the auto down operation being unable to fully open the power wind ...
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual
- For your information
- Pictorial index
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Lexus Display Audio system
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual
0.0111