Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual: Installation

INSTALLATION

PROCEDURE

1. INSTALL REAR SEAT AIRBAG ASSEMBLY

(a) Install the rear seat airbag assembly with 2 new nuts.

Torque:

5.5 N·m {56 kgf·cm, 49 in·lbf}

NOTICE:

  • Do not reuse the nuts.
  • Make sure that the rear seatback frame sub-assembly is not deformed. If it is deformed, replace it with a new one.

(b) Engage the 6 clamps.

(c) Connect the rear seat airbag assembly connector.

(1) Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

*a

Correct

*b

Incorrect

*c

Yellow CPA

-

-

(2) Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

NOTICE:

  • When connecting any airbag connector, take care not to damage the airbag wire harness.
  • When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and upper part of the yellow CPA, as it may result in an insecure fit.

2. INSTALL RECLINING REMOTE CONTROL BEZEL

Click here

3. INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD

Click here

4. INSTALL RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY

Click here

5. INSTALL REAR SEAT UPPER RECLINING COVER

Click here

6. INSTALL REAR SEAT ARMREST ASSEMBLY

Click here

7. INSTALL NO. 1 SEAT ARMREST CAP

Click here

8. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY

Click here

9. INSTALL REAR SEATBACK COVER

Click here

10. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD

Click here

11. INSTALL REAR SEAT INNER RECLINING COVER

Click here

12. INSTALL CUP HOLDER ASSEMBLY

Click here

13. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY

Click here

14. INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE

Click here

15. INSTALL REAR SEAT COVER CAP

Click here

16. INSTALL REAR NO. 1 SEAT ASSEMBLY

Click here

17. PERFORM DIAGNOSTIC SYSTEM CHECK

Click here

    On-vehicle Inspection
    ON-VEHICLE INSPECTION CAUTION / NOTICE / HINT CAUTION: Be sure to correctly follow the removal and installation procedures for the rear seat airbag assemblies. PROCEDURE 1. INSPECT REAR SEAT AIRBAG AS ...

    Removal
    REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the re ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Airbag System: Curtain Shield Airbag Sensor Initialization Error (RH) (B1633)
    DESCRIPTION The side collision sensor RH circuit (bus 1) consists of the airbag sensor assembly, door side airbag sensor RH and rear airbag sensor RH. The door side airbag sensor RH and rear airbag sensor RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if ...

    Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Rear No. 1 Seat Inner Belt Assembly(for Captain Seat Type): Inspection
    INSPECTION PROCEDURE 1. INSPECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH (a) Measure the resistance according to the value(s) in the table below. Standard Resistance: Tester Connection Condition Specified Condition 1 - 2 Rear No. 1 RH seat belt unfastened Below 1 Ω Rear No. 1 ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2024 Copyright www.lexusrx.net
    0.0187