Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual: Steering Angle Sensor Failure (C1626)
DESCRIPTION
This DTC is stored if the clearance warning ECU assembly receives a signal via CAN communication from the steering sensor that indicates an internal malfunction.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1626 | Steering Angle Sensor Failure | A fail flag is transmitted from the steering sensor |
|
CAUTION / NOTICE / HINT
NOTICE:
-
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
.gif)
-
After replacing an ultrasonic sensor or the clearance warning ECU assembly, perform the necessary procedures (adjustment, calibration, initialization or registration).
Click here
- When continuing with the inspection, confirm that the necessary procedures (adjustment, calibration, initialization or registration) have been completed before proceeding.
PROCEDURE
| 1. | REPLACE STEERING SENSOR |
(a) Replace the steering sensor with a new or known good one.
Click here
|
.gif)
| 2. | CHECK DTC OUTPUT |
(a) Using the Techstream, check for DTCs according to the prompts on the screen.
Click here
HINT:
After turning the engine switch from off to on (IG), wait 4 seconds or more before
Body Electrical > Advanced Parking Guidance/ICS/Intuitive P/A > Trouble Codes(b) Clear the DTCs according to the screen on the Techstream.
Click here
(c) Recheck for DTCs.
| Result | Proceed to |
|---|---|
| DTC C1626 is output | A |
| DTC C1626 is not output | B |
| A | .gif) | REPLACE CLEARANCE WARNING ECU ASSEMBLY |
| B | | END (STEERING SENSOR DEFECTIVE) |
Open or Short in Steering Angle Sensor +B (C1625)
DESCRIPTION This DTC is stored if the clearance warning ECU assembly receives a signal via CAN communication from the steering sensor that indicates a power supply problem. DTC No. Detection Item ...
Communication Error From Clearance Sonar ECU to VSC (C164B)
DESCRIPTION The vehicle stability control system receives intelligent clearance sonar system information from the clearance warning ECU assembly via CAN communication. When it is determined that there ...
Other materials:
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Front Door Belt Moulding: Installation
INSTALLATION CAUTION / NOTICE / HINT HINT:
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
PROCEDURE 1. INSTALL FRONT DOOR BELT MOULDING ASSEMBLY Install in this Direction (a) Engage the 8 claws as shown in the illustration to install ...
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Camshaft Oil Control Valve (for Bank 2): On-vehicle Inspection
ON-VEHICLE INSPECTION PROCEDURE 1. REMOVE CAMSHAFT TIMING GEAR BOLT Click here 2. INSPECT CAMSHAFT TIMING GEAR BOLT (a) for intake side: (1) Check the stroke of the plunger in the center of the camshaft timing gear bolt. Standard Stroke: 4.5 mm (0.177 in.) or more HINT: When pressing the plu ...
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual
- For your information
- Pictorial index
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Lexus Display Audio system
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual
0.0424