Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual: Open or Short in Steering Angle Sensor +B (C1625)
DESCRIPTION
This DTC is stored if the parking assist ECU receives a signal via CAN communication from the steering sensor that indicates a power supply system problem.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1625 | Open or Short in Steering Angle Sensor +B | Open or short in steering angle sensor +B |
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
- Since the panoramic view monitor system has functions that use the CAN communication system, first confirm that there is no malfunction in the communication system by inspecting the CAN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.
-
When "!" is displayed on the multi-display assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.
Click here
.gif)
-
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.
Click here
- Inspect the fuses for circuits related to this system before performing the following procedure.
-
The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.
Click here
PROCEDURE
| 1. | CHECK HARNESS AND CONNECTOR (STEERING SENSOR POWER SOURCE) |
(a) Disconnect the steering sensor connector.
Click here
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J32-1 (ESS) - Body ground | Always | Below 1 Ω |
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| J32-4 (IG1) - J32-1 (ESS) | Engine switch on (IG) | 11 to 14 V |
| J32-5 (BAT) - J32-1 (ESS) | Always | 11 to 14 V |
| OK |  | REPLACE STEERING SENSOR |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
Back Camera Feedback Malfunction (C1622)
DESCRIPTION DTC C1622 is stored if the parking assist ECU judges as a result of its self check that the signals or signal lines between the parking assist ECU and the rear television camera assembly a ...
Steering Angle Sensor Failure (C1626)
DESCRIPTION This DTC is stored if the parking assist ECU receives a signal via CAN communication from the steering sensor that indicates an internal malfunction. DTC No. Detection Item DTC Dete ...
Other materials:
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Rear Wiper Rubber: Replacement
REPLACEMENT PROCEDURE 1. REMOVE REAR WIPER BLADE (w/o Rear No. 2 Seat) (a) Turn the engine switch on (IG). (b) Operate the rear wiper and when the rear wiper arm and blade assembly reach the point at which they reverse, turn the engine switch off. (c) Apply protective tape to the rear ...
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Lumbar Switch: Removal
REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front lumbar power seat switch removal/installation are shown below. Necessary Procedures After Parts Re ...
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual
- For your information
- Pictorial index
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Lexus Display Audio system
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual
0.0117