Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual: Removal
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during blind spot monitor buzzer removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced| Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
|
*1: When performing learning using the Techstream.
Click here | |||
| Disconnect cable from negative battery terminal | Memorize steering angle neutral point | Lane Control System | |
| Pre-collision System | |||
| Intelligent Clearance Sonar System*1 | |||
| Parking Assist Monitor System | | ||
| Panoramic View Monitor System | | ||
| Lighting System (w/ Automatic Headlight Beam Level Control System) | | ||
| Initialize back door lock | Power Door Lock Control System | | |
| Reset back door close position | Power Back Door System (w/ Outside Door Control Switch) | | |
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here .gif)
.png)
PROCEDURE
1. REMOVE TONNEAU COVER ASSEMBLY
Click here
2. REMOVE DECK BOARD ASSEMBLY
Click here
3. REMOVE REAR NO. 3 FLOOR BOARD
Click here
4. REMOVE REAR DECK FLOOR BOX
Click here
5. REMOVE REAR NO. 4 FLOOR BOARD
Click here
6. REMOVE FRONT DECK FLOOR BOX
Click here
7. REMOVE DECK SIDE TRIM BOX RH
Click here
8. REMOVE REAR FLOOR FINISH PLATE
Click here
9. REMOVE REAR DOOR SCUFF PLATE LH
Click here
10. REMOVE REAR SEAT ASSEMBLY LH
Click here
11. REMOVE UPPER QUARTER TRIM PAD LH
Click here
12. REMOVE REAR SEAT SIDE GARNISH LH
Click here
13. REMOVE REAR FLOOR FINISH SIDE PLATE LH
Click here
14. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
Click here
15. REMOVE ROPE HOOK ASSEMBLY
Click here
16. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY
Click here
17. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
Click here
18. REMOVE BLIND SPOT MONITOR BUZZER
| (a) Disconnect the connector. |
|
.png)
(b) Disengage the clamp and remove the blind spot monitor buzzer.
Installation
INSTALLATION PROCEDURE 1. INSTALL BLIND SPOT MONITOR BUZZER (a) Connect the connector. (b) Engage the clamp to install the blind spot monitor buzzer. 2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH Click ...
Television Camera (for Front)
ComponentsCOMPONENTS ILLUSTRATION *1 COOL AIR INTAKE DUCT SEAL *2 FRONT TELEVISION CAMERA ASSEMBLY *3 MILLIMETER WAVE RADAR SENSOR ASSEMBLY *4 TELEVISION CAMERA WIRE N*m (kg ...
Other materials:
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Audio And Visual System (for 12.3 Inch Display): Steering Pad Switch Circuit
DESCRIPTION This circuit sends an operation signal from the steering pad switch assembly to the radio receiver assembly. If there is an open in the circuit, the audio and visual system cannot be operated using the steering pad switch assembly. If there is a short in the circuit, the same condition a ...
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Automatic Transaxle System: Intermediate Shaft Speed Sensor "A" Circuit Short to Battery (P079112,P079114,P079131)
DESCRIPTION The transmission revolution sensor (NC) detects the rotation speed of the counter gear which shows the output shaft speed of automatic transaxle assembly. Based on the transmission revolution sensor (NC) signal and the transmission revolution sensor (NT and NC3) signals, the ECM controls ...
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual
- For your information
- Pictorial index
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Lexus Display Audio system
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual
0.0107