DESCRIPTION
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
---|---|---|---|---|---|
C060B11 | Left Electric Parking Brake Actuator Control Circuit Short to Ground |
|
| DTC stored | An electric parking brake system malfunction is displayed on the multi-information display. |
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Click here
PROCEDURE
1. | INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY |
(a) Turn the engine switch off.
(b) Make sure that there is no looseness at the locking part and the connecting part of the connectors.
OK:
The connector is securely connected.
(c) Disconnect the oS1 and o2 No. 2 parking brake wire assembly connectors.
(d) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(e) Measure the resistance according to the value(s) in the table below.
*a | Front view of No. 2 Parking Brake Wire Assembly | *b | (to wire harness connector) |
*c | (to Parking Brake Actuator Assembly LH) | - | - |
Standard Resistance:
Tester Connection | Condition | Specified Condition |
---|---|---|
oS1-1 or o2-2 (MRL+) - Body ground and other terminals | Always | 10 kΩ or higher |
oS1-2 or o2-1 (MRL-) - Body ground and other terminals | Always | 10 kΩ or higher |
NG | ![]() | REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY |
|
2. | CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY LH) |
(a) Turn the engine switch off.
(b) Make sure the No. 2 parking brake wire assembly is securely installed.
(c) Disconnect the A41 skid control ECU (brake actuator assembly) connector.
(d) Disconnect the o2 parking brake actuator assembly LH connector.
(e) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
---|---|---|
A41-3 (MRL+) or o2-2 (MRL+) - Body ground | Always | 10 kΩ or higher |
A41-2 (MRL-) or o2-1 (MRL-) - Body ground | Always | 10 kΩ or higher |
NG | ![]() | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
3. | INSPECT PARKING BRAKE ACTUATOR ASSEMBLY LH |
(a) Remove the parking brake actuator assembly LH.
Click here
(b) Inspect the parking brake actuator assembly LH.
Click here
OK | ![]() | REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) |
NG | ![]() | REPLACE PARKING BRAKE ACTUATOR ASSEMBLY LH |
Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Audio And Visual System (for 12.3 Inch Display): Radio Receiver Power Source Circuit
DESCRIPTION This is the power source circuit to operate the radio receiver assembly. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: Inspect the fuses for circuits related to this system before performing the following procedure. PROCEDURE 1. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBL ...
Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Audio And Visual System (for 12.3 Inch Display): Touch Pad Vibration Driver Malfunction (B155A)
DESCRIPTION This DTC is stored if the remote touch (remote operation controller assembly) detects a malfunction in itself, such as internal hardware failure or remote touch screen vibration driver malfunction. DTC No. Detection Item DTC Detection Condition Trouble Area B155A Touch Pad ...