DESCRIPTION
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
---|---|---|---|---|---|
C060B13 | Left Electric Parking Brake Actuator Control Circuit Open |
|
| DTC stored | An electric parking brake system malfunction is displayed on the multi-information display. |
WIRING DIAGRAM
Click here
CAUTION / NOTICE / HINT
NOTICE:
Click here
PROCEDURE
1. | INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY |
(a) Turn the engine switch off.
(b) Make sure that there is no looseness at the locking part and the connecting part of the connectors.
OK:
The connector is securely connected.
(c) Disconnect the oS1 and o2 No. 2 parking brake wire assembly connectors.
(d) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(e) Measure the resistance according to the value(s) in the table below.
*a | Front view of No. 2 Parking Brake Wire Assembly | *b | (to wire harness connector) |
*c | (to Parking Brake Actuator Assembly LH) | - | - |
Standard Resistance:
Tester Connection | Condition | Specified Condition |
---|---|---|
oS1-1 - o2-2 (MRL+) | Always | Below 1 Ω |
oS1-1 - Other terminals | Always | 10 kΩ or higher |
oS1-2 - o2-1 (MRL-) | Always | Below 1 Ω |
oS1-2 - Other terminals | Always | 10 kΩ or higher |
NG | ![]() | REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY |
|
2. | CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY LH) |
(a) Turn the engine switch off.
(b) Make sure the No. 2 parking brake wire assembly is securely installed.
(c) Disconnect the A41 skid control ECU (brake actuator assembly) connector.
(d) Disconnect the o2 parking brake actuator assembly LH connector.
(e) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
---|---|---|
A41-3 (MRL+) - o2-2 (MRL+) | Always | Below 1 Ω |
A41-2 (MRL-) - o2-1 (MRL-) | Always | Below 1 Ω |
NG | ![]() | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
3. | INSPECT PARKING BRAKE ACTUATOR ASSEMBLY LH |
(a) Remove the parking brake actuator assembly LH.
Click here
(b) Inspect the parking brake actuator assembly LH.
Click here
OK | ![]() | REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) |
NG | ![]() | REPLACE PARKING BRAKE ACTUATOR ASSEMBLY LH |
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Lighting System (w/o Automatic Headlight Beam Level Control System): Data List / Active Test
DATA LIST / ACTIVE TEST DATA LIST NOTICE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not. HINT: Using the Techstream to read the Data List allows the values or states of ...
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Combination Meter: Disassembly
DISASSEMBLY PROCEDURE 1. REMOVE COMBINATION METER GLASS (for Optitron Meter Type) (a) Disengage the 8 claws to remove the combination meter glass. 2. REMOVE COMBINATION METER GLASS (for TFT Meter Type) (a) Disengage the 9 claws to remove the combination meter glass. ...