DESCRIPTION
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
|---|---|---|---|---|---|
| C061013 | Right Electric Parking Brake Actuator Control Circuit Open |
|
| DTC stored | An electric parking brake system malfunction is displayed on the multi-information display. |
WIRING DIAGRAM
Click here
CAUTION / NOTICE / HINT
NOTICE:
Click here
PROCEDURE
| 1. | INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY |
(a) Turn the engine switch off.
(b) Make sure that there is no looseness at the locking part and the connecting part of the connectors.
OK:
The connector is securely connected.
(c) Disconnect the oR1 and o1 No. 1 parking brake wire assembly connectors.
(d) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(e) Measure the resistance according to the value(s) in the table below.
| *a | Front view of No. 1 Parking Brake Wire Assembly | *b | (to wire harness connector) |
| *c | (to Parking Brake Actuator Assembly RH) | - | - |
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| oR1-1 - o1-2 (MRR+) | Always | Below 1 Ω |
| oR1-1 - Other terminals | Always | 10 kΩ or higher |
| oR1-2 - o1-1 (MRR-) | Always | Below 1 Ω |
| oR1-2 - Other terminals | Always | 10 kΩ or higher |
| NG | | REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY |
|
| 2. | CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY RH) |
(a) Turn the engine switch off.
(b) Make sure the No. 1 parking brake wire assembly is securely installed.
(c) Disconnect the A41 skid control ECU (brake actuator assembly) connector.
(d) Disconnect the o1 parking brake actuator assembly RH connector.
(e) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A41-13 (MRR+) - o1-2 (MRR+) | Always | Below 1 Ω |
| A41-12 (MRR-) - o1-1 (MRR-) | Always | Below 1 Ω |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
| 3. | INSPECT PARKING BRAKE ACTUATOR ASSEMBLY RH |
(a) Remove the parking brake actuator assembly RH.
Click here
(b) Inspect the parking brake actuator assembly RH.
Click here
| OK | | REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) |
| NG | | REPLACE PARKING BRAKE ACTUATOR ASSEMBLY RH |
Right Electric Parking Brake Actuator Control Circuit Short to Battery (C061012)
Right Electric Parking Brake Actuator Control Circuit Short to Ground or Open (C061014)Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Seat Heater Switch (for Rear Side): Installation
INSTALLATION CAUTION / NOTICE / HINT CAUTION: Wear protective gloves. Sharp areas on the seat frame may injure your hands. PROCEDURE 1. INSTALL REFRESHING SEAT SWITCH (for Console Box) (a) Engage the 2 guides. (b) Install the refreshing seat switch with the 3 screws. 2. INSTALL CONSOLE REAR END PANE ...
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Airbag System: Short in Side Squib (RH) Circuit (B1820-B1823)
DESCRIPTION The front side squib RH circuit consists of the airbag sensor assembly and front seat airbag assembly RH. The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met. These DTCs are stored when a malfunction is detected in the front side squib RH ...