DESCRIPTION
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
---|---|---|---|---|---|
C06132A | Right Electric Parking Brake Actuator Signal Stuck In Range |
|
| DTC stored | An electric parking brake system malfunction is displayed on the multi-information display. |
Vehicle Condition | ||||
---|---|---|---|---|
Pattern 1 | Pattern 2 | Pattern 3 | ||
Diagnosis Condition | Electric parking brake operating | ○ | ○ | ○ |
Malfunction Status | Motor lock detected | ○ | - | - |
Gear lock detected | - | ○ | - | |
Free spinning detected | - | - | ○ | |
Detection Time | - | - | - | |
Number of Trips | 1 trip | 1 trip | 1 trip |
WIRING DIAGRAM
Click here
CAUTION / NOTICE / HINT
NOTICE:
Click here
PROCEDURE
1. | CHECK DTC |
(a) Using the Techstream, check for DTCs other than DTC C06132A.
Chassis > Brake/EPB > Trouble Codes Result | Proceed to |
---|---|
Only DTC C06132A is output | A |
DTCs other than C06132A are output | B |
B | GO TO DIAGNOSTIC TROUBLE CODE CHART |
|
2. | INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY |
(a) Turn the engine switch off.
(b) Make sure that there is no looseness at the locking part and the connecting part of the connectors.
OK:
The connector is securely connected.
(c) Disconnect the oR1 and o1 No. 1 parking brake wire assembly connectors.
(d) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(e) Measure the resistance according to the value(s) in the table below.
*a | Front view of No. 1 Parking Brake Wire Assembly | *b | (to wire harness connector) |
*c | (to Parking Brake Actuator Assembly RH) | - | - |
Standard Resistance:
Tester Connection | Condition | Specified Condition |
---|---|---|
oR1-1 - o1-2 (MRR+) | Always | Below 1 Ω |
oR1-1 or o1-2 (MRR+) - Body ground and other terminals | Always | 10 kΩ or higher |
oR1-2 - o1-1 (MRR-) | Always | Below 1 Ω |
oR1-2 or o1-1 (MRR-) - Body ground and other terminals | Always | 10 kΩ or higher |
NG | REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY |
|
3. | CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY RH) |
(a) Turn the engine switch off.
(b) Make sure the No. 1 parking brake wire assembly is securely installed.
(c) Disconnect the A41 skid control ECU (brake actuator assembly) connector.
(d) Disconnect the o1 parking brake actuator assembly RH connector.
(e) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
---|---|---|
A41-13 (MRR+) - o1-2 (MRR+) | Always | Below 1 Ω |
A41-12 (MRR-) - o1-1 (MRR-) | Always | Below 1 Ω |
A41-13 (MRR+) or o1-2 (MRR+) - Body ground | Always | 10 kΩ or higher |
A41-12 (MRR-) or o1-1 (MRR-) - Body ground | Always | 10 kΩ or higher |
NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
4. | INSPECT REAR BRAKE AND PARKING BRAKE ACTUATOR ASSEMBLY RH (CHECK FOR ROTATING PARTS THAT ARE STUCK AND FOR FREE SPINNING ACTUATORS) |
(a) Enter rear brake pad replacement mode.
Click here
(b) Turn the engine switch off.
(c) Check that the rotating parts are not seized or the actuator is not spinning freely.
(1) Check that the parking brake actuator assembly RH is installed properly to the rear brake caliper and that it is not spinning freely.
For the parking brake actuator assembly RH removal procedure: Click here
(2) Check that there is no damage to the rotating parts from the parking brake actuator assembly RH to the rear brake caliper.
(3) Inspect the parking brake actuator assembly RH and check that it operates correctly.
Click here
(4) Check that the rear brake caliper threaded part rotates and that the rear disc brake piston moves outward.
HINT:
For the check procedures, refer to the parking brake forced release method when not using the Techstream.
Click here
HINT:
Return to normal mode after work is complete.
Click here
Result | Proceed to |
---|---|
Parking brake actuator assembly RH is malfunctioning | A |
Other than parking brake actuator assembly RH is malfunctioning | B |
A | REPLACE PARKING BRAKE ACTUATOR ASSEMBLY RH |
B | REPAIR OR REPLACE ABNORMAL PARTS |
Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Dynamic Torque Control Awd System: Terminals Of Ecu
TERMINALS OF ECU CHECK 4WD ECU ASSEMBLY (a) Measure the voltage and resistance of the connector. Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition R10-10 (4WDS) - R10-4 (GND) P - W-B AWD lock mode switch signal Engine switch on (IG) AWD lock ...
Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Rear Crankshaft Oil Seal: Components
COMPONENTS ILLUSTRATION *1 REAR ENGINE OIL SEAL *2 NO. 1 CRANKSHAFT POSITION SENSOR PLATE *3 DRIVE PLATE AND RING GEAR SUB-ASSEMBLY *4 REAR DRIVE PLATE SPACER N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part MP grease Adhesive 1324 ★ Pr ...