Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual: Replacement

REPLACEMENT

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear drive shaft oil seal replacement are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Rear wheel alignment adjustment

Calibration

  • VSC disabled or malfunctioning
  • DTCs are output
  • Slip indicator light illuminated
  • ABS warning light illuminated

Suspension, tires, etc.

(The vehicle height changes because of suspension or tire replacement)

  • Ultrasonic sensor detection angle
  • Ultrasonic sensor detection angle registration
  • Intelligent clearance sonar system
  • Intuitive parking assist system (w/ Intelligent Clearance Sonar System)

Rear television camera assembly optical axis (Back camera position setting)

Parking assist monitor system

for Initialization:

for Calibration:

  • Parking assist ECU initialization
  • Adjust steering angle

Panoramic view monitor system

for Initialization:

for Calibration:

Initialize No. 1 headlight ECU sub-assembly LH

Lighting System (w/ Automatic Headlight Beam Level Control System)

Gas leaks from exhaust system*1

Inspection after repair

  • Poor idle, etc.
  • Engine start function, etc.

*1: for RH Side

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. REMOVE REAR DRIVE SHAFT ASSEMBLY

Click here

2. REMOVE REAR DRIVE SHAFT SNAP RING

Click here

3. REMOVE REAR DRIVE SHAFT OIL SEAL

(a) Using SST, remove the rear drive shaft oil seal from the rear differential carrier assembly.

SST: 09308-00010

*1

Rear Drive Shaft Oil Seal

4. INSTALL REAR DRIVE SHAFT OIL SEAL

(a) Using SST and a hammer, install a new rear drive shaft oil seal into the rear differential carrier assembly.

SST: 09223-46011

SST: 09631-32020

NOTICE:

  • Install the rear drive shaft oil seal uniformly so that it is driven in straight.
  • Do not excessively tap in the rear drive shaft oil seal.
  • Do not damage the rear drive shaft oil seal.
  • Make sure to install the rear drive shaft oil seal as specified, otherwise a malfunction such as an oil leak may occur.

Standard Distance (A):

8.2 to 8.8 mm (0.323 to 0.346 in.)

*1

Rear Drive Shaft Oil Seal

(b) Apply a light coat of MP grease to the lip of the new rear drive shaft oil seal.

5. INSTALL REAR DRIVE SHAFT SNAP RING

Click here

6. INSTALL REAR DRIVE SHAFT ASSEMBLY

Click here

    Components
    COMPONENTS ILLUSTRATION *1 REAR DRIVE SHAFT ASSEMBLY *2 REAR DRIVE SHAFT OIL SEAL *3 REAR DRIVE SHAFT SNAP RING *4 DIFFERENTIAL INSPECTION PLUG *5 REAR DIFFERENTIAL DRAIN PLU ...

    Steering Knuckle
    ComponentsCOMPONENTS ILLUSTRATION *A Nut Type A *B Nut Type B *1 FRONT LOWER BALL JOINT ASSEMBLY *2 STEERING KNUCKLE *3 FRONT AXLE HUB SUB-ASSEMBLY *4 FRONT DISC BRAKE DU ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Main Body Ecu: Components
    COMPONENTS ILLUSTRATION *1 COWL SIDE TRIM BOARD LH *2 FRONT DOOR SCUFF PLATE LH *3 HOOD LOCK CONTROL LEVER SUB-ASSEMBLY *4 INSTRUMENT PANEL GARNISH LH *5 INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU *6 LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY ...

    Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Cruise Control Main Switch: Inspection
    INSPECTION PROCEDURE 1. INSPECT CRUISE CONTROL MAIN SWITCH (a) Measure the resistance according to the value(s) in the table below. *a Component without harness connected (Cruise Control Switch) - - Standard Resistance: Tester Connection Condition Specified Condition 1 (ECC) ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2025 Copyright www.lexusrx.net
    0.0175