INSTALLATION
PROCEDURE
1. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY
(a) Move the shift lever to N.
(b) Temporarily install the park/neutral position switch assembly to the automatic transaxle case sub-assembly with the 2 bolts.
NOTICE:
Before installing the park/neutral position switch assembly, remove any dirt or rust on the manual valve lever shaft sub-assembly. Be sure to install the park/neutral position switch assembly straight along the manual valve lever shaft sub-assembly while being careful not to deform the plate spring that supports the manual valve lever shaft sub-assembly. If the plate spring is deformed, the park/neutral position switch assembly cannot be installed correctly.
(c) Install a new lock plate and the lock nut to the park/neutral position switch assembly.
Torque:
6.9 N·m {70 kgf·cm, 61 in·lbf}
(d) Temporarily install the transmission control shaft lever to the park/neutral position switch assembly.
(e) Turn the transmission control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches. |
|
(f) Remove the transmission control shaft lever from the park/neutral position switch assembly.
(g) Align the protrusion with the neutral basic line. |
|
(h) Hold the park/neutral position switch assembly in that position and tighten the 2 bolts.
Torque:
5.4 N·m {55 kgf·cm, 48 in·lbf}
(i) Using a screwdriver, bend down the tabs of the lock plate.
(j) Install the transmission control shaft lever to the manual valve lever shaft sub-assembly with the nut.
Torque:
16 N·m {163 kgf·cm, 12 ft·lbf}
(k) Connect the park/neutral position switch assembly connector.
2. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
(a) Connect the transmission control cable assembly to the transmission control shaft lever with the nut.
Torque:
12 N·m {122 kgf·cm, 9 ft·lbf}
NOTICE:
Before connecting the transmission control cable assembly, check that the park/neutral position switch assembly and shift lever are in neutral.
3. INSTALL BATTERY
(a) Install the battery clamp bolt to the battery carrier sub-assembly.
(b) Install the battery tray and battery.
(c) Install the battery insulator.
(d) Install the battery clamp sub-assembly with the bolt and nut.
Torque:
5.4 N·m {55 kgf·cm, 48 in·lbf}
(e) Connect the cable to the positive (+) battery terminal and tighten the nut.
Torque:
5.4 N·m {55 kgf·cm, 48 in·lbf}
(f) Engage the 2 claws to close the battery terminal cap.
4. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
5. INSTALL INLET AIR CLEANER ASSEMBLY
Click here
6. INSTALL COOL AIR INTAKE DUCT SEAL
Click here
7. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY OPERATION
Click here
8. INSPECT SHIFT LEVER POSITION
Click here
9. ADJUST SHIFT LEVER POSITION
Click here
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Sfi System: Active Control Engine Mount System
DESCRIPTION LOCATION *1 No. 2 Vacuum Switching Valve Assembly (for Active Control Engine Mount) *2 Front Engine Mounting Insulator Assembly The active control engine mount system decreases engine vibration at a low engine speed using the No. 2 vacuum switching valve assembly (for active ...
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Fuel Lid Opener System: Problem Symptoms Table
PROBLEM SYMPTOMS TABLE HINT:
Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspect ...