MONITOR DESCRIPTION
This DTC is stored when a communication error occurs in the ECM.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P060B49 | Internal Control Module A/D Processing Performance Internal Electronic Failure | ECM main CPU communication error (1 trip detection logic). | ECM | Comes on | DTC stored | SAE Code: P060B |
MONITOR STRATEGY
| Related DTCs | P060B: Internal control module A/D processing performance |
| Required Sensors/Components (Main) | ECM |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 2 times |
| MIL Operation | Immediate |
| Sequence of Operation | None |
TYPICAL ENABLING CONDITIONS
| Monitor runs whenever the following DTCs are not stored | None |
TYPICAL MALFUNCTION THRESHOLDS
| AD converter | Fail |
CONFIRMATION DRIVING PATTERN
HINT:
Click here
Click here
HINT:
| Techstream Display | Description |
|---|---|
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
HINT:
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
CAUTION / NOTICE / HINT
NOTICE:
After turning engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
| 1. | READ OUTPUT DTC (DTC P060B49) |
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Clear the DTCs.
Powertrain > Engine > Clear DTCs(e) Turn the engine switch off and turn the Techstream off.
(f) Disconnect the Techstream.
(g) Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
(h) Connect the cable to the negative (-) battery terminal.
(i) Connect the Techstream to the DLC3.
(j) Turn the engine switch on (IG).
(k) Turn the Techstream on.
(l) Wait 16 seconds or more.
(m) Enter the following menus: Powertrain / Engine / Trouble Codes.
(n) Read the DTCs.
Powertrain > Engine > Trouble Codes| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P060B49 is output | B |
| A | | CHECK FOR INTERMITTENT PROBLEMS |
| B | | REPLACE ECM |
Internal Control Module Monitoring Processor Performance Watchdog/Safety MCU Failure (P060A47)
Internal Control Module Accelerator Pedal Position Performance Internal Electronic Failure (P060D49)Lexus RX (RX 350L, RX450h) 2016-2026 Owners Manual > Before driving: Trailer towing (vehicles
without towing
package)
Lexus does not recommend towing a trailer with your vehicle. Lexus also
does
not recommend the installation of a tow hitch or the use of a tow hitch carrier
for a wheelchair, scooter, bicycle, etc. Your vehicle is not designed for
trailer
towing or for the use of tow hitch mounted carriers.
...
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Electric Parking Brake System: Left Electric Parking Brake Actuator Control Circuit Short to Ground or Open (C060B14)
DESCRIPTION DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note C060B14 Left Electric Parking Brake Actuator Control Circuit Short to Ground or Open
Diagnosis Condition:
Engine switch on (IG)
Malfunction Status:
When the ECU power supply is normal, a mal ...