Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual: Lost Communication with Rear Gate Module (U0230)

Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual / Power Source & Network / Networking / Can Communication System / Lost Communication with Rear Gate Module (U0230)

DESCRIPTION

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Note

U0230

Lost Communication with Rear Gate Module

No communication from the multiplex network door ECU continues.
  • Multiplex network door ECU branch line or connector
  • Power source circuit of multiplex network door ECU
  • Multiplex network door ECU ground circuit
  • Multiplex network door ECU

HINT:

The main body ECU (multiplex network body ECU) stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 1.

HINT:

This diagnostic procedure is for when DTC U0230 is output by the main body ECU (multiplex network body ECU) (Techstream display: Main Body).

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  • After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
  • DTC check procedure: Turn the engine switch on (IG) and wait for at least 20 seconds.
  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

HINT:

  • Operating the engine switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

PROCEDURE

1.

RECONFIRM DTC OUTPUT

(a) Reconfirm DTCs.

HINT:

If DTC U1002 is output from Main Body of the main body ECU (multiplex network body ECU), this indicates a sub bus 1 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 1.

Body Electrical > Main Body > Trouble Codes

Result

Proceed to

DTC U1002 is not output from the main body ECU (multiplex network body ECU) (Techstream display: Main Body)

A

DTC U1002 is output from the main body ECU (multiplex network body ECU) (Techstream display: Main Body)

B
B

GO TO DIAGNOSTIC PROCEDURE INDICATED BY OUTPUT DTC

A

2.

CHECK FOR OPEN IN SUB BUS 1 LINES (MULTIPLEX NETWORK DOOR ECU BRANCH LINE)

(a) Disconnect the cable from the negative (-) battery terminal.

(b) Disconnect the Z16 multiplex network door ECU connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Z16-39 (CANP) - Z16-40 (CANN)

Cable disconnected from negative (-) battery terminal

54 to 69 Ω

*a

Front view of wire harness connector

(to Multiplex Network Door ECU)
NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (MULTIPLEX NETWORK DOOR ECU)
OK

3.

CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

(a) Disconnect the Z17 multiplex network door ECU connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Z17-10 (GND) - Body ground

Cable disconnected from negative (-) battery terminal

Below 1 Ω

*a

Front view of wire harness connector

(to Multiplex Network Door ECU)

(c) Reconnect the cable to the negative (-) battery terminal.

(d) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

Z16-20 (ECUB) - Body ground

Always

11 to 14 V

Z17-1 (B) - Body ground

Always

11 to 14 V

Z16-18 (IG) - Body ground

Engine switch on (IG)

11 to 14 V
OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
    Lost Communication with "Seat Control Module A" (U0208)
    DESCRIPTION DTC No. Detection Item DTC Detection Condition Trouble Area Note U0208 Lost Communication with "Seat Control Module A" No communication from the position control ECU and ...

    Lost Communication with Tilt & (U1115)
    DESCRIPTION DTC No. Detection Item DTC Detection Condition Trouble Area Note U1115 Lost Communication with Tilt & Telescopic Module No communication from the multiplex tilt and ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Seat: Seat Heater Control(for Front Side)
    ComponentsCOMPONENTS ILLUSTRATION *1 SEAT HEATER CONTROL SUB-ASSEMBLY - - RemovalREMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during seat heate ...

    Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Roof Headlining (w/ Rear No. 2 Seat): Reassembly
    REASSEMBLY PROCEDURE 1. INSTALL NO. 1 ROOF WIRE (a) When using a new roof headlining assembly: (1) Using a knife, cut the roof headlining assembly at the markings as shown in the illustration. *A for Standard Roof *B for Sliding Roof *a Marking *b Cut (b) Apply butyl tape as s ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2026 Copyright www.lexusrx.net
    0.0098