Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual: Check Bus 2 Line for Short to GND

Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual / Power Source & Network / Networking / Can Communication System / Check Bus 2 Line for Short to GND

DESCRIPTION

There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminal 18 (CA4H) of the network gateway ECU and terminal 4 (CG) of the DLC3, or terminal 17 (CA4L) of the network gateway ECU and terminal 4 (CG) of the DLC3.

Symptom

Trouble Area

No resistance exists between terminal 18 (CA4H) of the network gateway ECU and terminal 4 (CG) of the DLC3, or terminal 17 (CA4L) of the network gateway ECU and terminal 4 (CG) of the DLC3.
  • Short in CAN main bus line
  • Short in CAN branch line
  • Network gateway ECU
  • ECM

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  • After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
  • DTC check procedure: Drive the vehicle at a speed of 60 km/h (37 mph) or more for 5 minutes or more. And drive the vehicle with the dynamic radar cruise control system operated for 4 seconds or more.
  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

    Click here

HINT:

  • Operating the engine switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

PROCEDURE

1.

CHECK FOR SHORT TO GND IN CAN BUS LINE (NETWORK GATEWAY ECU)

(a) Disconnect the cable from the negative (-) battery terminal.

*A

for DLC3 Connector Type A

*B

for DLC3 Connector Type B

*1

DLC3

-

-

*a

Front view of wire harness connector

(to Network Gateway ECU)

-

-

(b) Disconnect the J75 network gateway ECU connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

for DLC3 Connector Type A

Tester Connection

Condition

Specified Condition

J75-18 (CA4H) - J12-4 (CG)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

J75-17 (CA4L) - J12-4 (CG)
for DLC3 Connector Type B

Tester Connection

Condition

Specified Condition

J75-18 (CA4H) - J141-4 (CG)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

J75-17 (CA4L) - J141-4 (CG)
OK

REPLACE NETWORK GATEWAY ECU

NG

2.

CHECK FOR SHORT TO GND IN CAN BUS LINE (ECM)

(a) Reconnect the J75 network gateway ECU connector.

(b) Disconnect the A37 ECM connector.

(c) Measure the resistance according to the value(s) in the table below.

*A

for DLC3 Connector Type A

*B

for DLC3 Connector Type B

*1

DLC3

-

-

*a

Front view of wire harness connector

(to ECM)

-

-

Standard Resistance:

for DLC3 Connector Type A

Tester Connection

Condition

Specified Condition

A37-13 (CANH) - J12-4 (CG)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

A37-26 (CANL) - J12-4 (CG)
for DLC3 Connector Type B

Tester Connection

Condition

Specified Condition

A37-13 (CANH) - J141-4 (CG)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

A37-26 (CANL) - J141-4 (CG)
OK

REPLACE ECM

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (ECM - NETWORK GATEWAY ECU)
    Check Bus 2 Line for Short to +B
    DESCRIPTION There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminal 18 (CA4H) of the network gateway ECU and terminal 16 (BAT) of the DLC3, or t ...

    Open in Bus 3 Main Bus Line
    DESCRIPTION There may be an open circuit in one of the bus 3 main lines when the resistance between terminals 6 (CA3H) and 21 (CA3L) of the network gateway ECU is 70 Ω or higher. Symptom Trouble ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Fuel Lid Opener System: Problem Symptoms Table
    PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspect ...

    Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Safety Connect System: Emergency Call Switch Illumination Circuit
    WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Safety Connect System. Click here Inspect the fuses for circuits rel ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2026 Copyright www.lexusrx.net
    0.0099