DATA LIST / ACTIVE TEST
DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Main Body or Smart Access / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Main Body > Data List| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Communication D-Door Motor | Connection status between power window regulator motor assembly (for driver door) and main body ECU (multiplex network body ECU) | OK or STOP | OK: Connected STOP: Not Connected | DTC is output if an error occurs in LIN communication. |
| Communication P-Door Motor | Connection status between power window regulator motor assembly (for front passenger door) and main body ECU (multiplex network body ECU) | OK or STOP | OK: Connected STOP: Not Connected | DTC is output if an error occurs in LIN communication. |
| Communication RR-Door Motor | Connection status between power window regulator motor assembly (for rear RH door) and main body ECU (multiplex network body ECU) | OK or STOP | OK: Connected STOP: Not Connected | DTC is output if an error occurs in LIN communication. |
| Communication RL-Door Motor | Connection status between power window regulator motor assembly (for rear LH door) and main body ECU (multiplex network body ECU) | OK or STOP | OK: Connected STOP: Not Connected | DTC is output if an error occurs in LIN communication. |
| Communication Slide Roof | Connection status between main body ECU (multiplex network body ECU) and sliding roof ECU (sliding roof drive gear sub-assembly)*1 or sliding roof ECU (sliding roof drive gear assembly)*2 | OK or STOP | OK: Connected STOP: Not Connected | DTC is output if an error occurs in LIN communication. |
| Communication Master SW | Connection status between multiplex network master switch assembly and main body ECU (multiplex network body ECU) | OK or STOP | OK: Connected STOP: Not Connected | DTC is output if an error occurs in LIN communication. |
| Communication Sliding Sunshade ECU | Connection status between roof sunshade ECU (sliding roof drive gear assembly) and main body ECU (multiplex network body ECU)*2 | OK or STOP | OK: Connected STOP: Not Connected | DTC is output if an error occurs in LIN communication. |
| The Number of DTC | Number of DTCs | 0 to 255 | Number of stored DTCs | - |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| # Codes | Number of DTCs | 0 to 255 | Number of stored DTCs | - |
Terminals Of Ecu
Dtc Check / ClearLexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Air Conditioning System: BUS IC Communication Malfunction (B1497/97)
DESCRIPTION Front Air Conditioning System The air conditioning harness assembly connects the air conditioning amplifier assembly and the servo motors. The air conditioning amplifier assembly supplies power and sends operation instructions to each servo motor through the air conditioning harness asse ...
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Accelerator Pedal: On-vehicle Inspection
ON-VEHICLE INSPECTION PROCEDURE 1. INSPECT ACCELERATOR PEDAL SENSOR ASSEMBLY (a) Connect the Techstream to the DLC3. (b) Turn the engine switch on (IG). (c) Turn the Techstream on. (d) Enter the following menus: Powertrain / Engine / Data List / Accelerator Position Sensor No. 1 Voltage and Accelera ...