Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual: Adjustment

Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual / Vehicle Exterior / Door / Hatch / Rear Door / Adjustment

ADJUSTMENT

CAUTION / NOTICE / HINT

*a

Centering Bolt

*b

Standard Bolt

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.
  • Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.
  • The specified torque for standard bolts is shown in the standard bolt chart.

    Click here

PROCEDURE

1. INSPECT REAR DOOR

(a) Check that the clearance measurements of areas a through j are within each standard range.

Standard Clearance

Area

Measurement

Area

Measurement

a

-2.0 to 2.0 mm (-0.0787 to 0.0787 in.)

b

2.1 to 6.1 mm (0.0827 to 0.240 in.)

c

3.65 to 6.65 mm (0.144 to 0.262 in.)

d

-0.5 to 2.5 mm (-0.0197 to 0.0984 in.)

e

4.7 to 7.7 mm (0.185 to 0.303 in.)

f

-1.5 to 1.5 mm (-0.0591 to 0.0591 in.)

g

2.0 to 5.0 mm (0.0787 to 0.197 in.)

h

-1.5 to 1.5 mm (-0.0591 to 0.0591 in.)

i

-1.2 to 1.2 mm (-0.0472 to 0.0472 in.)

j

2.3 to 4.7 mm (0.0906 to 0.185 in.)

2. ADJUST REAR DOOR

NOTICE:

Make sure to turn the ignition switch off when adjusting door lock strikers.

(a) Using SST, loosen the 4 hinge bolts on the vehicle body and adjust the door position.

SST: 09812-00020

(b) Tighten the 4 hinge bolts on the vehicle body after adjustment.

Torque:

32.5 N·m {331 kgf·cm, 24 ft·lbf}

(c) Loosen the 4 hinge bolts on the door and adjust the door position.

(d) Tighten the 4 hinge bolts on the door after adjustment.

Torque:

32.5 N·m {331 kgf·cm, 24 ft·lbf}

(e) Disengage the 4 claws to remove the rear door lock striker cover.

(f) Using a T40 "TORX" socket wrench, slightly loosen the 2 striker mounting screws.

(g) Using a brass bar and a hammer, hit the striker to adjust its position.

(h) Using a T40 "TORX" socket wrench, tighten the 2 striker mounting screws after adjustment.

Torque:

23 N·m {235 kgf·cm, 17 ft·lbf}

(i) Engage the 4 claws to install the rear door lock striker cover.
    Disassembly
    DISASSEMBLY CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during ...

    Reassembly
    REASSEMBLY CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The following procedure is for the LH side. PROCEDURE 1. PRECAUTION NOTICE: After turning the engin ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Front Brake: Inspection
    INSPECTION PROCEDURE 1. INSPECT BRAKE CYLINDER AND PISTON (a) Check the front disc brake cylinder bore and front disc brake piston for rust and scoring. If necessary, replace the front disc brake cylinder assembly and front disc brake piston. 2. INSPECT PAD LINING THICKNESS (a) Using a ruler, mea ...

    Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Lighting System (w/o Automatic Headlight Beam Level Control System): Headlight Dimmer Switch Circuit
    DESCRIPTION The main body ECU (multiplex network body ECU) receives the following switch information: Light control switch in DRL OFF*, tail, head, AUTO position Dimmer switch in high, low or high flash (pass) position *: w/ DRL OFF Switch WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2026 Copyright www.lexusrx.net
    0.011