Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual: Removal
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during height control sensor sub-assembly RH removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced| Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
| Disconnect cable from negative battery terminal | Memorize steering angle neutral point | Lane Control System | |
| Pre-collision system | |||
| Intelligent clearance sonar system*1 | |||
| Parking Assist Monitor System | | ||
| Panoramic View Monitor System | | ||
| Lighting System (w/ Automatic Headlight Beam Level Control System) | | ||
| Initialize back door lock | Power door lock control system | | |
| Reset back door close position | Power Back Door System (w/ Outside Door Control Switch) | | |
| Rear height control sensor sub-assembly RH | Initialize No. 1 headlight ECU sub-assembly LH | Lighting System (w/ Automatic Headlight Beam Level Control System) | |
*1: When performing learning using the Techstream.
Click here .gif)
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
3. REMOVE REAR WHEEL (for RH Side)
Click here
4. REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH
| (a) Disconnect the connector. |
|
(b) Remove the bolt.
(c) Disengage the guide.
| (d) Remove the bolt. |
|
(e) Disengage the guide to disconnect the rear height control sensor sub-assembly RH.
(f) Remove the 2 nuts and rear height control sensor sub-assembly RH.
NOTICE:
If the rear height control sensor sub-assembly RH has been struck or dropped, replace it with a new one.
Components
COMPONENTS ILLUSTRATION *1 REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY - - N*m (kgf*cm, ft.*lbf): Specified torque - - ...
Inspection
INSPECTION PROCEDURE 1. INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH (a) Connect 3 dry cell batteries (1.5 V) in series. NOTICE: Do not use rechargeable batteries as they may not output a voltag ...
Other materials:
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Front Seat Outer Belt Assembly: Inspection
INSPECTION PROCEDURE 1. INSPECT FRONT SEAT OUTER BELT ASSEMBLY (a) Check the seat belt tension reducer operation. CAUTION: Do not apply battery voltage to the pretensioner connector. (1) Connect a positive (+) lead from the battery to terminal 1 of the seat belt tension reducer connector and a ne ...
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Lin Communication System: Front Passenger Side Door ECU Communication Stop (B2322)
DESCRIPTION This DTC is stored when LIN communication between the power window regulator motor assembly RH and main body ECU (multiplex network body ECU) stops for 10 seconds or more. DTC No. Detection Item DTC Detection Condition Trouble Area B2322 Front Passenger Side Door ECU Commu ...
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual
- For your information
- Pictorial index
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Lexus Display Audio system
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual
0.0125