DESCRIPTION
The multiplex network master switch assembly sends the mirror adjust switch signals to the main body ECU (multiplex network body ECU) via LIN communication. The main body ECU (multiplex network body ECU) then sends the received mirror adjust switch signals to each outer mirror control ECU assembly via CAN communication. Based on this signal, each outer mirror control ECU assembly operates the vertical and horizontal mirror motors to adjust the mirror surface position.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Click here
Click here
PROCEDURE
| 1. | READ VALUE USING TECHSTREAM |
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Master Switch / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Master Switch > Data List| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Mirror Selection SW (L) | Mirror select switch signal for LH mirror | OFF or ON | OFF: Mirror select switch off ON: Mirror select switch L switch on | - |
| Mirror Selection SW (R) | Mirror select switch signal for RH mirror | OFF or ON | OFF: Mirror select switch off ON: Mirror select switch R switch on | - |
| Mirror Position SW (L) | Mirror adjust switch signal (Left) | OFF or ON | OFF: Mirror adjust switch not pressed left ON: Mirror adjust switch pressed left | Check with the mirror select switch L or R switch on |
| Mirror Position SW (R) | Mirror adjust switch signal (Right) | OFF or ON | OFF: Mirror adjust switch not pressed right ON: Mirror adjust switch pressed right | Check with the mirror select switch L or R switch on |
| Mirror Position SW (Up) | Mirror adjust switch signal (Up) | OFF or ON | OFF: Mirror adjust switch not pressed up ON: Mirror adjust switch pressed up | Check with the mirror select switch L or R switch on |
| Mirror Position SW (Dwn) | Mirror adjust switch signal (Down) | OFF or ON | OFF: Mirror adjust switch not pressed down ON: Mirror adjust switch pressed down | Check with the mirror select switch L or R switch on |
| Tester Display |
|---|
| Mirror Selection SW (L) |
| Mirror Selection SW (R) |
| Mirror Position SW (L) |
| Mirror Position SW (R) |
| Mirror Position SW (Up) |
| Mirror Position SW (Dwn) |
OK:
On the Techstream screen, ON or OFF is displayed accordingly.
| NG | | REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY |
|
| 2. | REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
(a) Temporarily replace the main body ECU (multiplex network body ECU) with a new or known good one.
Click here
|
| 3. | CHECK POWER MIRROR CONTROL OPERATION |
(a) Check the electrical remote control mirror function.
Click here
OK:
Electrical remote control mirror function operates normally.
| OK | | END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE) |
| NG | | REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY |
Front Passenger Side Power Mirror cannot be Adjusted with Power Mirror Switch
Mirror Heater does not Operate with Rear Defogger SwitchLexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Valve Body Assembly: Disassembly
DISASSEMBLY PROCEDURE 1. REMOVE MANUAL VALVE (a) Remove the manual valve from the transmission valve body assembly. (b) Remove the E-ring and separate the manual valve connecting rod from the manual valve. *1 Manual Valve Connecting Rod *2 Manual Valve *3 ...
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Smart Access System With Push-button Start (for Entry Function): System Diagram
SYSTEM DIAGRAM
This is a detailed diagram related to the certification ECU (smart key ECU assembly).
This is a detailed diagram related to the main body ECU (multiplex network body ECU). Component Function Front door outside handle assembly Receives request signals from ...