INSTALLATION
CAUTION / NOTICE / HINT
HINT:
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
2. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY
(a) Install the rear door inside locking cable assembly as shown in the illustration.
| Install in this Direction |
3. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY
(a) Install the rear door lock remote control cable assembly as shown in the illustration.
| Install in this Direction |
4. INSTALL REAR DOOR LOCK COVER SUB-ASSEMBLY
(a) Engage the 2 claws as shown in the illustration.
| Install in this Direction |
| (b) Engage the 2 claws to install the rear door lock cover sub-assembly as shown in the illustration. |
|
5. INSTALL REAR DOOR LOCK ASSEMBLY
NOTICE:
(a) Apply MP grease to the sliding parts of the rear door lock assembly.
(b) When reusing the rear door lock assembly:
(1) Install a new door lock wiring harness seal to the rear door lock assembly.
(c) Connect the rear door lock assembly to the release plate of the rear door outside handle frame sub-assembly, and set it to the rear door panel.
| *a | Release Plate |
| Install in this Direction |
HINT:
Make sure that the release plate of the rear door outside handle frame sub-assembly is securely connected to the rear door lock assembly.
(d) Using a T30 "TORX" socket wrench, install the rear door lock assembly with the 3 screws.
Torque:
5.5 N·m {56 kgf·cm, 49 in·lbf}
6. INSTALL REAR DOOR GLASS SUB-ASSEMBLY
Click here
7. INSTALL REAR DOOR REAR GUIDE SEAL
Click here
8. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY
Click here
9. CONNECT REAR DOOR WEATHERSTRIP
(a) Connect the rear door weatherstrip.
10. INSTALL REAR DOOR GLASS RUN
Click here
11. INSTALL REAR DOOR SERVICE HOLE COVER
Click here
12. INSTALL REAR DOOR NO. 2 TRIM BRACKET
Click here
13. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP
Click here
14. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY
Click here
15. INSTALL COURTESY LIGHT ASSEMBLY
Click here
16. INSTALL REAR DOOR ARMREST COVER
Click here
17. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL
Click here
18. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG
Click here
19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
20. INITIALIZE POWER WINDOW CONTROL SYSTEM
Click here
21. INSPECT POWER WINDOW OPERATION
Click here
Inspection
RemovalLexus RX (RX 350L, RX450h) 2016-2026 Owners Manual > Using the other interior
features: Other interior features
Sun visors
To set the visor in the forward position,
flip it down.
To set the visor in the side position,
flip down, unhook, and swing it to the
side.
To use the side extender, place the
visor in the side position, then slide it
backward.
Vanity mirrors
Slide the cover to ope ...
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Occupant Classification System: Front Occupant Classification Sensor LH Collision Detection (B1785)
DESCRIPTION DTC B1785 is stored when the occupant detection ECU receives a collision detection signal sent by the front occupant classification sensor LH in the case of an accident. DTC B1785 is also stored when the front seat assembly RH is subjected to a strong impact, even if an actual accident d ...