REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear center seat outer belt assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced| Replaced Part or Performed Procedure | Necessary Procedures | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| Disconnect cable from negative battery terminal | Memorize steering angle neutral point | Lane Control System | |
| Pre-collision system | |||
| Intelligent clearance sonar system*1 | |||
| Parking assist monitor system | | ||
| Panoramic view monitor system | | ||
| Lighting system (w/ Automatic Headlight Beam Level Control System) | | ||
| Initialize back door lock | Power door lock control system | | |
| Reset back door close position | Power Back Door System (w/ Outside Door Control Switch) | |
*1: When performing learning using the Techstream.
Click here
CAUTION:
Click here
NOTICE:
After the engine switch is turned off, the radio receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) battery terminal.
PROCEDURE
1. REMOVE REAR NO. 1 SEAT ASSEMBLY RH
Click here
2. REMOVE REAR SEAT COVER CAP RH
Click here
3. REMOVE NO. 1 RECLINING ADJUSTER RELEASE HANDLE RH
Click here
4. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH
Click here
5. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD
Click here
6. REMOVE REAR NO. 1 SEAT RECLINING ADJUSTER INSIDE COVER
Click here
7. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
| (a) Remove the bolt to disconnect the anchor of the rear center seat outer belt assembly. |
|
8. REMOVE REAR SEATBACK COVER RH
Click here
9. REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY RH
Click here
10. REMOVE REAR SEAT UPPER RECLINING COVER RH
Click here
11. REMOVE RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY RH
Click here
12. REMOVE SEAT BELT ANCHOR COVER CAP
Click here
13. REMOVE REAR SEAT SHOULDER BELT COVER
Click here
14. REMOVE SEPARATE TYPE REAR SEATBACK COVER WITH PAD
Click here
15. REMOVE REAR SEATBACK EDGE PROTECTOR
Click here
16. REMOVE REAR CENTER SEAT OUTER BELT ASSEMBLY
| (a) Remove the 2 nuts. |
|
(b) Disengage the 2 guides to remove the rear center seat outer belt assembly.
Inspection
InstallationLexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Audio And Visual System (for 12.3 Inch Display): Sending Malfunction (Navigation to APGS) (U0073,U0100,U0129,U0140,U0155,U0164,U023B,U0265,U1110)
DESCRIPTION These DTCs are stored when a malfunction occurs in the CAN communication circuit. DTC No. Detection Item DTC Detection Condition Trouble Area U0073 Sending Malfunction (Navigation to APGS) CAN bus connection error CAN communication system U0100 Engine ECU Communi ...
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Heating / Air Conditioning: Relay
On-vehicle InspectionON-VEHICLE INSPECTION PROCEDURE 1. INSPECT PTC HEATER RELAY (a) Measure the resistance according to the value(s) in the table below. *a Component without harness connected (PTC HTR NO. 1) *b Component without harness connected (PTC HTR NO. 2) *c Component without ...