Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual: Removal
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear seat inner belt assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced| Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
| Disconnect cable from negative battery terminal | Memorize steering angle neutral point | Lane Control System | |
| Pre-collision system | |||
| Intelligent clearance sonar system*1 | |||
| Lighting system (w/ Automatic Headlight Beam Level Control System) | | ||
| Parking assist monitor system | | ||
| Panoramic view monitor system | | ||
| Initialize back door lock | Power door lock control system | | |
| Reset back door close position | Power Back Door System (w/ Outside Door Control Switch) | |
*1: When performing learning using the Techstream.
Click here .gif)
CAUTION:
-
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here
- Wear protective gloves. Sharp areas on the parts may injure your hands.
.png)
NOTICE:
After the engine switch is turned off, the radio receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) battery terminal.
PROCEDURE
1. REMOVE REAR SEAT ASSEMBLY RH
Click here
2. REMOVE REAR SEAT COVER CAP RH (for Manual Seat)
Click here
3. REMOVE NO. 1 RECLINING ADJUSTER RELEASE HANDLE RH (for Manual Seat)
Click here
4. REMOVE POWER SEAT SWITCH ASSEMBLY (for Power Seat)
Click here
5. DISCONNECT SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD
Click here
6. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD
Click here
7. REMOVE REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH
(a) Disengage each clamp.
(b) Disconnect the connector.
| (c) Loosen the bolt and remove the rear seat 3 point type belt assembly RH. HINT: The bolt cannot be removed from the rear seat 3 point type belt assembly RH. |
|
Components
COMPONENTS ILLUSTRATION *A for Manual Seat *B for Power Seat *1 NO. 1 RECLINING ADJUSTER RELEASE HANDLE RH *2 POWER SEAT SWITCH ASSEMBLY *3 REAR SEAT 3 POINT TYPE BELT ASSEMB ...
Inspection
INSPECTION PROCEDURE 1. INSPECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH (a) Measure the resistance according to the value(s) in the table below. Standard Resistance: Tester Connection Conditi ...
Other materials:
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Safety Connect System: Precaution
PRECAUTION PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE BATTERY TERMINAL NOTICE: When disconnecting the cable from the negative (-) battery terminal, initialize the following systems after the terminal is reconnected. System Name See Procedure Lane Control System Pre-collision ...
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Airbag System: Short in Curtain Shield Airbag (RH) Squib Circuit (B1830-B1833)
DESCRIPTION The curtain shield squib RH circuit consists of the airbag sensor assembly and curtain shield airbag assembly RH. The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met. These DTCs are stored when a malfunction is detected in the curtain shie ...
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual
- For your information
- Pictorial index
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Lexus Display Audio system
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual
0.0137