DESCRIPTION
The side collision sensor LH circuit (bus 1) consists of the airbag sensor assembly, door side airbag sensor LH and rear airbag sensor LH.
The door side airbag sensor LH and rear airbag sensor LH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.
These DTCs are stored when a malfunction is detected in the rear airbag sensor LH.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Test Mode / Check Mode |
|---|---|---|---|---|---|
| B1635 | Curtain Shield Airbag Sensor (LH) |
|
| Comes on | Does not apply to test/check mode |
| B1637 | Curtain Shield Airbag Sensor Lost Communication (LH) |
|
| Comes on | Does not apply to test/check mode |
WIRING DIAGRAM
Click here
CAUTION / NOTICE / HINT
NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
PROCEDURE
| 1. | CHECK REAR AIRBAG SENSOR LH |
| (a) Turn the engine switch off. |
|
(b) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Interchange the rear airbag sensor LH with RH and connect the connectors.
(d) Connect the cable to the negative (-) battery terminal.
(e) Turn the engine switch on (IG), and wait for at least 60 seconds.
(f) Clear the DTCs stored in memory.
Body Electrical > SRS Airbag > Clear DTCs(g) Turn the engine switch off.
(h) Turn the engine switch on (IG), and wait for at least 60 seconds.
(i) Check for DTCs.
Body Electrical > SRS Airbag > Trouble CodesHINT:
Codes other than DTCs B1630, B1632, B1635 and B1637 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTC B1635 or B1637 is output. | A |
| DTC B1630 or B1632 is output. | B |
| DTCs B1630, B1632, B1635 and B1637 are not output. | C |
(j) Turn the engine switch off.
(k) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(l) Return the rear airbag sensor LH and RH to their original positions and connect the connectors.
| A | | REPLACE AIRBAG SENSOR ASSEMBLY |
| B | | REPLACE REAR AIRBAG SENSOR LH |
| C | | USE SIMULATION METHOD TO CHECK |
Curtain Shield Airbag Sensor Initialization Error (RH) (B1633)
Lost Communication with Front Door Pressure Sensor RH (B166D,B166E)Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Rear Power Seat Control System(for Third Row): Initialization
INITIALIZATION 1. INITIALIZATION (INITIAL POSITION CLEAR) NOTICE: It is necessary to perform initialization (initial position clear) if any of the following conditions are met.
The fold seat control ECU has been replaced with a used one.
The No. 2 seat cushion frame sub-assembly RH, No. 2 seat ...
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Door Courtesy Light: Components
COMPONENTS ILLUSTRATION *A for Front Door *B for Bulb Type *1 COURTESY LIGHT ASSEMBLY *2 COURTESY LIGHT BULB *3 COURTESY LIGHT LENS *4 COURTESY LIGHT COVER *5 COURTESY LIGHT HOUSING - - ILLUSTRATION *A for Rear Door *B for Bulb Type *1 COURT ...