Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual: How To Proceed With Troubleshooting

CAUTION / NOTICE / HINT

HINT:

  • Use the following procedure to troubleshoot the blind spot monitor system.
  • *: Use the Techstream.

PROCEDURE

1.

VEHICLE BROUGHT TO WORKSHOP

NEXT

2.

CUSTOMER PROBLEM ANALYSIS

HINT:

If there are any scratches or impact marks on the rear bumper, perform the blind spot monitor beam axis confirmation. If any abnormalities are found, perform the blind spot monitor sensor installation condition inspection.

NEXT

3.

INSPECT BATTERY VOLTAGE

(a) Measure the battery voltage.

Standard Voltage:

11 to 14 V

If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.

NEXT

4.

CHECK CAN COMMUNICATION SYSTEM*

(a) Use the Techstream to check if the CAN communication system is functioning normally.

Click here

Result

Proceed to

CAN communication system DTCs are not output.

A

CAN communication system DTCs are output.

B

B

GO TO CAN COMMUNICATION SYSTEM

A

5.

CHECK FOR DTC AND FREEZE FRAME DATA*

(a) Refer to DTC Check / Clear for the blind spot monitor system.

Click here

Body Electrical > Blind Spot Monitor Master > Trouble Codes Body Electrical > Blind Spot Monitor Slave > Trouble Codes

(b) Record or print DTCs and freeze frame data, if necessary.

Click here

Result

Proceed to

DTCs are not output.

A

DTCs are output.

B

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

A

6.

PROBLEM SYMPTOMS TABLE

(a) Refer to Problem Symptoms Table.

Click here

Result

Proceed to

Fault is not listed in Problem Symptoms Table.

A

Fault is listed in Problem Symptoms Table.

B

HINT:

If the symptom does not recur and no DTCs are output, attempt to reproduce the symptoms.

Click here

B

GO TO PROBLEM SYMPTOMS TABLE

A

7.

PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM*

(a) Refer to Terminals of ECU.

Click here

(b) Refer to Diagnosis System.

Click here

(c) Refer to Data List / Active Test.

Click here

NEXT

8.

ADJUST, REPAIR OR REPLACE

Result

Proceed to

When adjusting or repairing

A

When replacing

B

B

GO TO STEP 10

A

9.

CLEAR DTC*

(a) Clear the DTCs.

Click here

Body Electrical > Blind Spot Monitor Master > Clear DTCs Body Electrical > Blind Spot Monitor Slave > Clear DTCs
NEXT

GO TO STEP 10

10.

PERFORM BEAM AXIS CONFIRMATION

(a) Confirm the blind spot monitor beam axis display and perform the blind spot monitor beam axis adjustment.

Click here

NEXT

11.

PERFORM CONFIRMATION TEST*

NEXT

END

    System Description
    SYSTEM DESCRIPTION GENERAL (a) The blind spot monitor system has a blind spot monitor function and RCTA function. (1) Blind spot monitor function The blind spot monitor function is a function that ...

    Customize Parameters
    CUSTOMIZE PARAMETERS CUSTOMIZE BLIND SPOT MONITOR SYSTEM (a) Customizing with the Techstream NOTICE: When the customer requests a change in a function, first make sure that the function can be cust ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Front Door Speaker: Components
    COMPONENTS ILLUSTRATION *A for Driver Side *B for Front Passenger Side *1 COURTESY LIGHT ASSEMBLY *2 DOOR ARMREST COVER *3 FRONT DOOR INSIDE HANDLE BEZEL PLUG *4 FRONT DOOR NO. 1 STIFFENER CUSHION *5 FRONT DOOR TRIM BOARD SUB-ASSEMBLY *6 FRONT NO. 1 SPEAKER AS ...

    Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Rear Power Seat Control System(for Second Row): Fold Seat Switch Circuit
    DESCRIPTION When the fold seat switch assembly is operated, a switch operation signal is sent to the fold seat control ECU. According to the signal received, the fold seat control ECU operates the fold motor to perform a fold or return operation of the rear seatback. WIRING DIAGRAM PROCEDURE 1. ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2024 Copyright www.lexusrx.net
    0.0178