REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the lower No. 1 instrument panel airbag assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced Replacement Part or Procedure | Necessary Procedures | Effects / Inoperative when not performed | Link |
---|---|---|---|
Disconnect cable from negative battery terminal | Memorize steering angle neutral point | Lane control system | |
Pre-collision system | |||
Intelligent clearance sonar system*1 | |||
Lighting system (w/ Automatic Headlight Beam Level Control System) | | ||
Parking assist monitor system | | ||
Panoramic view monitor system | | ||
Initialize back door lock | Power door lock control system | | |
Reset back door close position | Power back door system | |
*1: When performing learning using the Techstream.
Click here
PROCEDURE
1. PRECAUTION
CAUTION:
Be sure to read Precaution thoroughly before servicing.
Click here
NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
3. REMOVE FRONT DOOR SCUFF PLATE LH
w/o Rear No. 2 Seat: Click here
w/ Rear No. 2 Seat: Click here
4. REMOVE COWL SIDE TRIM BOARD LH
Click here
5. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Click here
6. REMOVE INSTRUMENT PANEL GARNISH LH
Click here
7. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
Click here
8. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
Click here
9. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL
Click here
10. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL
Click here
11. REMOVE INSTRUMENT CLUSTER FINISH PANEL ORNAMENT
Click here
12. REMOVE LOWER INSTRUMENT FINISH PANEL SUB
Click here
13. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY
CAUTION:
When storing the lower No. 1 instrument panel airbag assembly, keep the airbag deployment side facing upward.
![]() | Deployment Side |
(a) Check that the engine switch is off.
(b) Check that the cable is disconnected from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Remove the 2 bolts. |
|
(d) Disengage the 3 claws, hook and 2 guides to separate the lower No. 1 instrument panel airbag assembly.
NOTICE:
When separating the lower No. 1 instrument panel airbag assembly, do not pull the airbag wire harness.
(e) Using a screwdriver with its tip wrapped with protective tape, release the airbag connector lock. |
|
(f) Disconnect the airbag connector to remove the lower No. 1 instrument panel airbag assembly.
NOTICE:
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Intuitive Parking Assist System (w/ Intelligent Clearance Sonar System): Rear Sensor Communication Malfunction (C1AED)
DESCRIPTION This DTC is stored when there is an open or short circuit in the communication line between the rear sensors and the ECU, or when there is a malfunction in a rear sensor. DTC No. Detection Item DTC Detection Condition Trouble Area C1AED Rear Sensor Communication Malfunctio ...
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Sfi System: Internal Control Module Monitoring Processor Performance Watchdog/Safety MCU Failure (P060A47)
MONITOR DESCRIPTION The main CPU and sub CPU of the ECM perform data communication between each other. The main CPU monitors the communications and WDC pulses from the sub CPU. When the signal malfunctions below are detected, this DTC is stored. DTC No. Detection Item DTC Detection Condition ...