REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during No. 2 clearance warning buzzer removal/installation are shown below.
Necessary Procedures after parts removed/installed/replaced| Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
|
*1: When performing learning using the Techstream.
Click here | |||
| Disconnect cable from negative battery terminal | Memorize steering angle neutral point | Lane Control System | |
| Pre-collision System | |||
| Intelligent Clearance Sonar System*1 | |||
| Lighting System (w/ Automatic Headlight Beam Level Control System) | | ||
| Parking Assist Monitor System | | ||
| Panoramic View Monitor System | | ||
| Initialize back door lock | Power Door Lock Control System | | |
| Reset back door close position | Power Back Door System (w/ Outside Door Control Switch) | | |
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here
PROCEDURE
1. REMOVE TONNEAU COVER ASSEMBLY
Click here
2. REMOVE DECK BOARD ASSEMBLY
Click here
3. REMOVE REAR NO. 3 FLOOR BOARD
Click here
4. REMOVE REAR DECK FLOOR BOX
Click here
5. REMOVE REAR NO. 4 FLOOR BOARD
Click here
6. REMOVE DECK SIDE TRIM BOX RH
Click here
7. REMOVE REAR FLOOR FINISH PLATE
Click here
8. REMOVE REAR DOOR SCUFF PLATE RH
HINT:
Use the same procedure as for the LH side.
Click here
9. REMOVE REAR SEAT ASSEMBLY RH
Click here
10. REMOVE UPPER QUARTER TRIM PAD RH
HINT:
Use the same procedure as for the LH side.
Click here
11. REMOVE REAR SEAT SIDE GARNISH RH
HINT:
Use the same procedure as for the LH side.
Click here
12. REMOVE REAR FLOOR FINISH SIDE PLATE RH
HINT:
Use the same procedure as for the LH side.
Click here
13. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
Click here
14. REMOVE ROPE HOOK ASSEMBLY
HINT:
Use the same procedure as for the LH side.
Click here
15. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY
Click here
16. REMOVE RECLINING REMOTE CONTROL BEZEL RH (w/o Rear Power Seat System)
Click here
17. REMOVE FOLD SEAT SWITCH ASSEMBLY (w/ Rear Power Seat System)
Click here
18. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH
Click here
19. REMOVE NO. 2 CLEARANCE WARNING BUZZER
| (a) Disengage the clamp. |
|
(b) Disconnect the connector to remove the No. 2 clearance warning buzzer.
Components
InstallationLexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Occupant Classification System: Passenger Side Buckle Switch Circuit Malfunction (B1771)
DESCRIPTION The passenger side buckle switch circuit consists of the occupant detection ECU and passenger side buckle switch (front seat inner belt assembly RH). DTC B1771 is stored when a malfunction is detected in the passenger side buckle switch circuit. DTC No. Detection Item DTC Detectio ...
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Power Mirror Control System (w/o Memory): Problem Symptoms Table
PROBLEM SYMPTOMS TABLE NOTICE: If the battery voltage is low, the mirror heater function may not operate. When "Operation of Electrical Items Restricted." is displayed on the multi-information display in the combination meter assembly, check the Data List item "Battery Control Count (Body ECU)". Cli ...