Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual: Brake Hydraulic Pressure Malfunction (C164F)
DESCRIPTION
When a malfunction signal sent from the skid control ECU via CAN communication is detected by the clearance warning ECU assembly, DTC C164F is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C164F | Brake Hydraulic Pressure Malfunction | Brake master cylinder brake fluid pressure abnormal | Vehicle stability control system |
CAUTION / NOTICE / HINT
NOTICE:
-
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
.gif)
-
After replacing an ultrasonic sensor or the clearance warning ECU assembly, perform the necessary procedures (adjustment, calibration, initialization or registration).
Click here
PROCEDURE
| 1. | CHECK DTC OUTPUT |
(a) Using the Techstream, check for DTCs according to the prompts on the screen.
Click here
HINT:
After turning the engine switch from off to on (IG), wait 4 seconds or more before checking for DTCs.
Body Electrical > Advanced Parking Guidance/ICS/Intuitive P/A > Trouble Codes(b) Clear the DTCs according to the screen on the Techstream.
Click here
(c) Recheck for DTCs.
Click here
HINT:
- DTC C164F is stored when a malfunction signal sent from the vehicle stability control system is detected.
- If the malfunctioning part has been repaired or replaced before rechecking for DTCs, DTC C164F will not be output again.
-
If DTC C164F is output frequently, duplicate the conditions that cause the problem symptoms and perform the inspection again, even though the DTC was not output when rechecking for DTCs.
Click here
| Result | Proceed to |
|---|---|
| DTC C164F is output | A |
| DTC C164F is not output | B |
| A |  | GO TO VEHICLE STABILITY CONTROL SYSTEM |
| B | | USE SIMULATION METHOD TO CHECK |
Stop Switch Circuit Malfunction (C164E)
DESCRIPTION When a stop light switch assembly circuit malfunction signal sent from the vehicle stability control system is detected by the clearance warning ECU assembly, DTC C164E is stored. DTC N ...
Outside Air Temperature Sensor (C1652)
DESCRIPTION When a malfunction signal sent from the air conditioning system via CAN communication is detected by the clearance warning ECU assembly, DTC C1652 is stored. DTC No. Detection Item ...
Other materials:
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Compressor: Disassembly
DISASSEMBLY PROCEDURE 1. REMOVE COOLER COMPRESSOR BRACKET (a) Disengage the clamp. (b) Remove the screw and cooler compressor bracket. 2. REMOVE MAGNET CLUTCH ASSEMBLY (a) Secure the compressor and magnetic clutch in a vise between aluminum plates. (b) Using SST, hold t ...
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Automatic Transaxle System: Shift Solenoid "A" Circuit Short to Battery or Open (P075015)
DESCRIPTION Changing gears is performed by the ECM turning the shift solenoid valves SL1, SL2, SL3, SL4, SL5, S1 and S2 on and off. If an open or short occurs in any of the shift solenoid valve circuits, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be driven. I ...
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual
- For your information
- Pictorial index
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Lexus Display Audio system
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual
0.0134