Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual: Stop Switch Circuit Malfunction (C164E)
DESCRIPTION
When a stop light switch assembly circuit malfunction signal sent from the vehicle stability control system is detected by the clearance warning ECU assembly, DTC C164E is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C164E | Stop Switch Circuit Malfunction | Stop light switch assembly circuit open | Vehicle stability control system |
CAUTION / NOTICE / HINT
NOTICE:
-
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
.gif)
-
After replacing an ultrasonic sensor or the clearance warning ECU assembly, perform the necessary procedures (adjustment, calibration, initialization or registration).
Click here
PROCEDURE
| 1. | CHECK DTC OUTPUT |
(a) Using the Techstream, check for DTCs according to the prompts on the screen.
Click here
HINT:
After turning the engine switch from off to on (IG), wait 4 seconds or more before checking for DTCs.
Body Electrical > Advanced Parking Guidance/ICS/Intuitive P/A > Trouble Codes(b) Clear the DTCs according to the screen on the Techstream.
Click here
(c) Recheck for DTCs.
Click here
HINT:
- DTC C164E is stored when a malfunction signal sent from the vehicle stability control system is detected.
- If the malfunctioning part has been repaired or replaced before rechecking for DTCs, DTC C164E will not be output again.
-
If DTC C164E is output frequently, duplicate the conditions that cause the problem symptoms and perform the inspection again, even though the DTC was not output when rechecking for DTCs.
Click here
| Result | Proceed to |
|---|---|
| DTC C164E is output | A |
| DTC C164E is not output | B |
| A | .gif) | GO TO VEHICLE STABILITY CONTROL SYSTEM |
| B | | USE SIMULATION METHOD TO CHECK |
Wheel Speed Sensor Malfunction (C164D)
DESCRIPTION This DTC is stored when the clearance warning ECU assembly receives a wheel speed sensor (front speed sensor RH or front speed sensor LH, rear speed sensor RH or rear speed sensor LH) abno ...
Brake Hydraulic Pressure Malfunction (C164F)
DESCRIPTION When a malfunction signal sent from the skid control ECU via CAN communication is detected by the clearance warning ECU assembly, DTC C164F is stored. DTC No. Detection Item DTC Det ...
Other materials:
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Smart Access System With Push-button Start (for Entry Function): New Key cannot be Registered
DESCRIPTION If a new electrical key transmitter sub-assembly could not be registered, wave interference or a malfunction of the certification ECU (smart key ECU assembly), electrical key transmitter sub-assembly, ID code box (immobiliser code ECU), steering lock ECU (steering lock actuator or upper ...
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Front Door Window Frame Moulding: Installation
INSTALLATION CAUTION / NOTICE / HINT HINT:
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
PROCEDURE 1. INSTALL FRONT DOOR FRONT WINDOW FRAME MOULDING (a) Using an air riveter or hand riveter with a nose piece, install the front door front wind ...
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual
- For your information
- Pictorial index
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Lexus Display Audio system
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual
0.0132