Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual: Wheel Speed Sensor Malfunction (C164D)
DESCRIPTION
This DTC is stored when the clearance warning ECU assembly receives a wheel speed sensor (front speed sensor RH or front speed sensor LH, rear speed sensor RH or rear speed sensor LH) abnormality signal from the vehicle stability control system via CAN communication.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C164D | Wheel Speed Sensor Malfunction | Front wheel speed sensor malfunction | Vehicle stability control system |
CAUTION / NOTICE / HINT
NOTICE:
-
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
.gif)
-
After replacing an ultrasonic sensor or the clearance warning ECU assembly, perform the necessary procedures (adjustment, calibration, initialization or registration).
Click here
PROCEDURE
| 1. | CHECK DTC OUTPUT |
(a) Using the Techstream, check for DTCs according to the prompts on the screen.
Click here
HINT:
After turning the engine switch from off to on (IG), wait 4 seconds or more before checking for DTCs.
Body Electrical > Advanced Parking Guidance/ICS/Intuitive P/A > Trouble Codes(b) Clear the DTCs according to the screen on the Techstream.
Click here
(c) Recheck for DTCs.
Click here
HINT:
- DTC C164D is stored when a malfunction signal sent from the vehicle stability control system is detected.
- If the malfunctioning part has been repaired or replaced before rechecking for DTCs, DTC C164D will not be output again.
-
If DTC C164D is output frequently, duplicate the conditions that cause the problem symptoms and perform the inspection again, even though the DTC was not output when rechecking for DTCs.
Click here
| Result | Proceed to |
|---|---|
| DTC C164D is output | A |
| DTC C164D is not output | B |
| A | .gif) | GO TO VEHICLE STABILITY CONTROL SYSTEM |
| B | | USE SIMULATION METHOD TO CHECK |
G Sensor Failure (C1647)
DESCRIPTION The clearance warning sonar ECU assembly communicates with the airbag sensor assembly*1 or yaw rate and acceleration sensor*2 via CAN communication, and if it is determined that the airbag ...
Stop Switch Circuit Malfunction (C164E)
DESCRIPTION When a stop light switch assembly circuit malfunction signal sent from the vehicle stability control system is detected by the clearance warning ECU assembly, DTC C164E is stored. DTC N ...
Other materials:
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Can Communication System: 4WD Control ECU Communication Stop Mode
DESCRIPTION Detection Item Symptom Trouble Area 4WD Control ECU Communication Stop Mode Either condition is met:
"Four Wheel Drive Control" is not displayed on the CAN Bus Check screen of the Techstream.
Click here
Communication system DTCs (DTCs that start with U) that corres ...
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Center Power Outlet Socket(for Rear No. 1 Seat): Removal
REMOVAL PROCEDURE 1. REMOVE REAR NO. 1 SEAT ASSEMBLY RH Click here 2. REMOVE REAR SEATBACK COVER Click here 3. REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY Click here 4. REMOVE CENTER ARMREST HINGE COVER LH Click here 5. REMOVE NO. 1 SEAT ARMREST ASSEMBLY Click here 6. REMOVE ARMREST ASSEMBLY ...
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual
- For your information
- Pictorial index
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Lexus Display Audio system
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual
0.0123